The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. Determine

Question:

The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. Determine the largest vertical force P that can be supported. The allowable tensile stress for the aluminum is Ïƒ_allow= 150 MPa.

45°

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Mechanics of Materials

ISBN: 978-0134319650

10th edition

Authors: Russell C. Hibbeler

See More Books

Question Posted: May 26, 2018 02:54 AM

See More Questions

The two aluminum rods support the vertical force of P = 20 kN. Determine their required diameters if the allowable tensile stress for the aluminum is Ï allow = 150 MPa. 45
The four-member "A" frame is supported at A and E by smooth collars and at G by a pin. All the other joints are ball-and-sockets. If the pin at G will fail when the resultant force there is Fmax,...
Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the ring at B, determine the angle Î¸ so that the average normal stress in each rod is...
Within the context of the planning cycle, the planning that takes place at the highest levels of the firm is called: A. detailed planning and control. B. strategic planning. C. operational planning....
Use the result of Exercise 61 to find a general form of the equation of the line having x-intercept (5, 0) and y-intercept (0, 6).
The observed baseline vector components in meters between two control stations are (3814.244, 470.348, 1593.650). The geocentric coordinates of the control stations are (1,162,247.650, 4,655,656.054,...
The $\frac{1}{2}$-in.-diameter hose shown in Fig. P8.68 can withstand a maximum pressure of $200 \mathrm{psi}$ without rupturing. Determine the maximum length, $\ell$, allowed if the friction...
Shouldice Hospital, the house that hernias built, is a converted country estate which gives the hospital a country club appeal. 1. How well is the hospital currently utilizing its beds? 2. Develop a...
Find resources that confirm the importance of budgeting to organizations and answer the question below. Using your work experience think about how budgets can influence the choices made by top...
You are an Examiner for the Refund Integrity Program in the GST/HST Audit Division of the Canada Revenue Agency (CRA). Using sophisticated analytical tools, you are able to identify GST/HST returns...
The bar has a cross-sectional area A and is subjected to the axial load P. Determine the average normal and average shear stresses acting over the shaded section, which is oriented at u from the...
Determine the required minimum thickness t of member AB and edge distance b of the frame if P = 9 kip and the factor of safety against failure is 2. The wood has a normal failure stress of Ï...
Go to the websites for project management tools (besides Microsoft Project), such as Apptivo (www.apptivo.com), GanttProject (www.ganttproject.biz), Gantter (www.gantter.com), and smartsheet...
ii. Calculate the approximate time delay for the following set of instructions, assuming fosc = 11.059MHZ MOV TMOD, #01H MOV TLO, #0 MOV THO, #0 AGAIN: DELAY: BACK: RET MOV R5, #04 ACALL DELAY CPL...
A 75-horsepower outboard motor at full throttle will rotate its propeller at exactly 4900 revolutions per min. Find the angular speed of the propeller in radians per second. 4900 rev per min radians...
Consider you have a stack whose elements in it are as follows. 5 4 3 2 < < topWhere the top element is 2.You need to get the following stack 6 5 4 3 2 < < topThe operations that needed to be...
Answer the question: Question 2 a. Discuss the four (4) Development Stages of the project team (12 marks) b. Give a detailed explanation for the steps you would take in preparing your first project...
Solve for r. 1.32 58.05= r-0.1 Enter your response rounded to 4 DECIMAL PLACES Number
When a car accelerates uniformly from rest, which of these quantities increases with time: acceleration, velocity, and/or distance traveled? Explain.
Write out the formula for the total costs of carrying and ordering inventory, and then use the formula to derive the EOQ model. Andria Mullins, financial manager of Webster Electronics, has been...
The bolt shank is subjected to a tension F. Determine the internal normal force, shear force, and moment at point C. Given: F = 80 lb a = 6 in B
Determine the normal force, shear force, and moment acting at sections passing through points B and C on the curved rod. Units Used: kip = 103 lb Given: F1 = 300 lb = 30 deg r = 2 ft F2 = 400 lb =...
The cantilevered rack is used to support each end of a smooth pipe that has total weight W. Determine the normal force, shear force, and moment that act in the arm at its fixed support A along a...
J is going to receive a 30-year annuity of 8,500 and L is going to receive perpetuity of 8,500. If the appropriate interest rate is 6%, how much more is L's cash flow worth?
. Assume that over the past 88 years, U.S. Treasury bills had an average return of 3.5% as compared to 6.1% on long-term government bonds. What was the average risk premium on the long-term...
The following data were gathered to use in reconciling the bank account of Bradford Company: Balance per bank $ 18,050 Balance per company records 10,040 Bank service charges 50 Deposit in transit...

The two aluminum rods AB and AC have diameters of 10 mm and 8 mm, respectively. Determine

Question:

45°

Step by Step Answer:

Assume failure of rod AB F AB 1178 kN From Eq 1 P ...View the full answer

Mechanics of Materials

Students also viewed these Sciences questions