FREE Trial

2.) A truck with axle loads of W = 19.6kN and W2 = 78.6kN on a wheel base of...

This problem has been solved!
Do you need an answer to a question different from the above? Ask your question!

Question:

2.) A truck with axle loads of W1 = 19.5kN and W2 = 78.6kN on a wheel base of d = 4.3m rolls across thebeam shown in the fig 

Transcribed Image Text:

2.) A truck with axle loads of W₁ = 19.6kN and W2 = 78.6kN on a wheel base of d = 4.3m rolls across the beam shown in the figure. Determine the following: 3m 25 m 22 m a.) Draw the influence line for the shear at C - 10pts b.) Draw the influence line for the moment at midspan of BC - 10pts c.) The maximum positive moment (kN-m) at the midspan of BC-5pts d.) The maximum negative moment (kN-m) at the midspan of BC-5pts e.) The maximum negative shear (kN) that can be developed in the beam-5pts

Expert Answer:


answer-question
View Solution
Create a free account to access the answer
Cannot find your solution?
Post a FREE question now and get an answer within minutes. * Average response time.
Posted Date: December 12, 2021 07:51:10
See More Questions

Students also viewed these accounting questions

Q:
Draw the influence line for the shear in panel CD of the girder. Determine the maximum negative live shear in panel CD due to a uniform live load of 500 lb/ft acting on the top beams. 8 ft 8 ft - 8...
A:
V CD max 50......
Q:
Draw the influence line for the shear at C. Plot numerical values every 1.5 m. Assume A is fixed and the support at Bis a roller. EI is constant. SA B 3 m 3 m
A:
The primary real beam and qualitative influence line a......
Q:
The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span length of 4.0 m. The beam is built of a wood member having cross-sectional dimensions...
A:
SIMPLE BEAM L 4 0 m q 50 kN m 1 Wood beam b 150 mm t 50 m......
Q:
Samples of size n = 5 are collected from a process every half hour. After 50 samples have been collected, we calculate. x = 20.0 and s 1.5. Assume that both charts exhibit control and that the...
A:
a b c......
Q:
List the principal lipids that are found in lipid rafts. Would a phospholipid with a high content of docosahexaenoic acid be a raft component?
A:
The principal lipids in lipid rafts are cholesterol and sphingolipids inc......
Q:
Good Homes Construction Company is about to begin the construction of a large new home. The companys president, Michael Dean, is currently planning the schedule for this project. Michael has...
A:
a 7 834 is saved by the new plan given......
Q:
Effective hiring policies that discriminate between marginal and highly ethical individuals contribute to an organizations success in preventing fraud. (True/False)
A:
The statement Effective hiring policies that discriminate between marginal and highly ethical indivi......
Q:
ListCo reports the following income for the current tax year. Operations ............. $92,000 Tax-exempt interest income ...... 19,000 Long-term capital gain ......... 60,000 ListCo holds earnings...
A:
a 1 Operations 92 000 Tax exempt interest income excludable 0 Long term capital gain 60 000 Taxable......
Q:
Suppose that the spot interest rate process (rt)t20 follows the Vasicek model, with the following parameters under the historical probability: speed a, level b and volatility o. Assume a constant...
A:
The Vasicek model is a one factor model for short rate dynamics which assumes that the short rate fo......
Q:
Problem No. 6 A computer chip factory produces chips with distribution N~(, ) = (100, 4). The production size is 350 chips/hour for 6 hours. (a) The first improvement reduced to (,) = (100, 2.5) 1....
A:
a 1 The factory is producing 350 chips per hour for a total of 21 50 chips in s......
Q:
Two amounts owing from the past were to be paid and the other was $925 from six months ago. Determine fully repay the debts. Allow for simple interest at 12%. past were to be paid today. One debt was...
A:
620 was taken 1 year at 12 simple interest Interest prt 6......
Q:
Objectives: - Program in the C++ programming language Understand the lexical analysis phase of program compilation The first phase of compilation is called scanning or lexical analysis. This phase...
A:
Below is a simple example of a C program that performs lexical analysis based on the token format you provided This program reads a source file provid......
Q:
Accounting records for Antoinette Designs (AD) for November show the following (each entry is the total of the actual entries for the account for the month): Account Titles Work-in-Process Inventory...
A:
Answer To answer the questions let s analyze the given information step by step a What was the finished goods inventory balance on November 30 The finished goods inventory balance on November 30 can b......
Q:
Discuss ANY THREE (3) political arguments for government intervention
A:
There are various political arguments advocating for government intervention in different aspects of society Here are three key arguments Economic Sta......
Q:
Discuss consumer decision making process in detail?
A:
The consumer decision making process is a series of steps that individuals go through when deciding to purchase a product or service This process is o......
Q:
What three critical factors should a company take into consideration when preparing its bid in order to enhance its chances of winning the bid
A:
When preparing a bid a company needs to carefully consider various factors to increase its chances of winning Here are three critical factors that sho......
Q:
Q.1) Give the distance vector table for networks shown below when (a) Each node knows only the distances to its immediate neighbors. (b) Each node has reported the information it had in the preceding...
A:
Answer 1 Answer 2 Link State Routing has two phases Reliable Flooding Initial state Each node knows the cost of its neighbors Final state Each node knows the entire graph Route Calculation Each node u......
Q:
Evaluate the function at the given value(s) of the independent variable. Simplify the results. (x) = cos 2x (a) (0) (b) (- /4) (c) (/3) (d) ()
A:
a b c......
Mechanical Engineering Science For Technicians Course 1st Edition - ISBN: 071313240X - Free Book