Question: 26. (4) What is the maximum material, least material, and virtual condition of the hole shown below? Hole MMC +.003 -.002 0.010 M 0.4371

26. (4) What is the maximum material, least material, and virtual condition of the hole shown below? Hole MMC +.003 -.002 0.010 M 0.4371 MMC LMC VC 0:015 M 27. (1) Assume the specified geometric and size tolerances shown on the part below are functionally required. What (if anything) must be done to make the given drawing correct to the ASME Y 14.5- 2009 or 2018 standards? - H Form Tolerance 28. (3) On the figure below, specify a derived median line (axis) straightness tolerance of .015 inches diameter over the entire length and a .005 inches diameter tolerance per inch of length of the pin. The tolerances are to be specified as applicable when the feature is at its maximum material condition. COR 1.250.005 010 .125 .001

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

When testing a change with PDSA: A test that does not achieve the desired results may mean what

Q1. You have identified a market opportunity for home media players that would cater for older members of the population. Many older people have difficulty in understanding the operating principles...

ttth Suppose that the sequence of bags {Bn | n N} is recursively enumerated by the computable function e(n, x) = fn(x), [7 marks] Hence prove that the set of all recursive bags cannot be recursively...

The excel homework assignment below has five tabs that cover five different topics: Net Present Value Analysis, Capital Budgeting and Cost of Capital, Working Capital, Management, Financial Ratio...

please need project report on all WYE 26 7120 21 90 (10 hrs * 3.60) = ? 36 3182 375 165 WYE 23,333 units (1,75,000 hrs -7.5 hrs pu) (2,80,000 hrs = 10 hrs pu) = 28,000 units 23,333 units 2 (23,333...

This is a capsim simulation question Calculating the Ideal Spot To calculate where the ideal spot is in each round, start with the segment center in the table below and then adjust for the offset....

I need help with how to do a DCF analysis for this Spotify case. Please can you show the explanation of the steps Thank you A. Using the information provided, what should SPs shares be trading at on...

Managing Scope Changes Case Study Scope changes on a project can occur regardless of how well the project is planned or executed. Scope changes can be the result of something that was omitted during...

can you help me with my cnc midterm asap please! thank you! 1) Which of the following ASME Y14.5 symbols represents a controlled radius? a. V b. R c. CR d. D 2) What does the diagram on the right...

Instructions for Emailing Homework - Please follo 1. Do NOT send your homework to my email address. Excel homework must be emailed to huxleyqba time and due date shown on the homework. Late homework...

Sarah Warren currently holds 400 shares of Nutri-Foods. The firm has 40,000 shares outstanding. The firm most recently had earnings available for common stockholders of $80,000, and its stock has...

please Use MATLAB to solve the below questions there are some kind of similar examples for this question which may help you to solve the below problems guideline examples questions no_trials = 8;...

QUESTION THREE ( 5 0 MARKS ) The following is the trial balance of Marvellous Ltd . The company has a 3 1 December year end. The information will be used to prepare statement of financial position...

On January 1, 2016, Monica Company acquired 70 percent of Young Company's outstanding common stock for $665,000. The fair value of the non-controlling interest at the acquisition date was $285,000....

On June 1, High Performance Cell Phones sold $ 23,000 of merchandise to Anthony Trucking Company on account. Anthony fell on hard times and on July 15 paid only $ 8,000 of the account receivable....

In a neutralization reaction, 18.06 g of KOH are reacted with 13.43 g of HNO3. What mass of H2O is produced, and what mass of which reactant is in excess?

Pitino acquired 90 percent of Breys outstanding shares on January 1, 2013, in exchange for $342,000 in cash. The subsidiarys stockholders equity accounts totaled $326,000 and the noncontrolling...

Oak Bucket Co., a manufacturer of wood buckets, had the following data for 2013: Sales ...............2,600 units Sales price ............$40 per unit Variable costs ..........$16 per unit Fixed...

Transactions made by Larkspur Co . for the month of March are shown below. The company performed $ 2 0 , 8 0 0 of services for customers on account. The company received $ 2 0 . 8 0 0 in cash from...

The first-order, irreversible, exothermic liquid-phase reaction A B is to be carried out in a jacketed CSTR. Species A and an inert I are fed to the reactor in equimolar amounts. The molar feed rate...

Sketch qualitatively the reactant, product, and activity profiles as a function of length at various times for a packed-bed reactor for each of the following cases. In addition, sketch the effluent...

What factors affect the enzymatic rate law and cell growth law both positive and negative ways.

=+a. What is the probability that a randomly chosen person from the population does not have the same blood type as that found at the crime scene?

=+John Wiley, New York, 1995). Suppose that a suspect is found whose blood type matches a rare blood type found at a crime scene. Let denote the frequency with which people in the population have...

=+b. If a 1 is received, what is the probability that a 1 was sent? Hint: Use the tree diagram from Exercise 6.