Question: 3 . 2 Determine the minimum size for a pin if it is in double shear and the factor of safety is 5 . 0

3.2 Determine the minimum size for a pin if it is in double shear and the factor of safety is 5.0 based on ultimate strength. The pin is made of structural steel and supports a load of 85 kN .
3 . 2 Determine the minimum size for a pin if it

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Question 1 The frame supports the point load P at point C. The pins at A and B have diameters of 50 mm and 64 mm respectively. Pin A is in single shear, while Pin B is in double shear, and both pins...

Q:

A concentrated load of \ ( P = 6 6 \ ) kips is applied to beam \ ( A B \ ) , as shown in the figure. Rod ( 1 ) has a diameter of 1 in . , and its yield strength is 1 1 5 ksi . Pin A is supported in a...

Q:

Rigid beam ABC is supported as shown in the figure. The pin connections at B , C , and D are each double shear connections, and the ultimate shear strength of the pin material is 5 8 0 MPa. Tie rod (...

Q:

P 4 . 9 Rigid beam ABC is supported as shown in Figure P 4 . 9 . The pin connections at B , C , and D are each double shear connections, and the ultimate shear strength of the pin material is 6 2 0...

Q:

5 - 5 Repeat Problem 5 - 1 by first plotting the failure loci in the A , B plane to scale; then, for each stress state, plot the load line and by graphical measurement estimate the factors of safety....

Q:

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

Q:

Consider the design of the pliers wrench presented and drawn according to the scale shown in Figure 1 ( each grid measures 0 . 5 cm on each side ) . Answer the following questions. ( a ) Draw the...

Q:

( c ) Using the forces determined in ( b ) , determine the stresses exerted on each of the four pins. The pins are circular in cross - section, 8 mm in diameter, and are all subjected to double shear...

Q:

Beam A B is supported as shown in the figure. Tie rod ( 1 ) is attached at B and C with double shear pin connections, while the pin at A is attached with a single shear connection. The pins at A , B...

Q:

The rigid structure ABD in Figure below is supported at B by a 35-mm-diameter tie rod (1) and at A by a 30-mm-diameter pin used in a single shear connection. The tie rod is connected at B and C by...

Q:

Two identical permanent dipoles, each consisting of charges +q and ?q separated by a distance s, are aligned along the x axis, a distance r from each other, where r ? s (see figure below). Show all...

Q:

Two liquids, A and B, show partial miscibility below 52.4C. The critical concentration at the upper critical temperature is x = 0.459, where x is the mole fraction of A. At 40.0C the two solutions in...

Q:

( Note: Exercises E 9 - 3 9 through E 9 - 4 1 are based on material from actual financial statements. In some instances, we added material to the facts presented in the financial statements to...

Q:

The degree to which sediment particles are rounded depends on all of the following EXCEPT: Group of answer choices the amount of time that has elapsed since the particle was attached to the outcrop...