$35)$what is the method for modelling building envelope components in HOT$2000$ when construction details $($eg$.$ lumber sizes and spacing, type of insulation...$)$ are known?

a$)$the code selector

b$)$a specific RSI$/$r$-$value

c$)$a user specified RSI$/$R$-$value

d$)$the composite RSI$/$R calculation

$36)$as part of the basic service data collection procedures what info must be collected for a central air conditioner?

a$)$equipment type, basement cooled or not cooled, model number rated capacity

b$)$airflow rate supply, circulation power, composite space cooling efficiency equipment type

c$)$installation centification number, instullation data, installer name and company AHRI number

d$)$coefficient of performance, during to basement, rating condition efficiency, cut$-$off temp

$37)$while provinding the basic service for a semi$-$detached house, the energy advisor encounters a living area that is located above an unheated garage, how should this living area be measured?

a$)$length and depth to the nearest $5$cm

b$)$length and depth to the nearest $7$ cm

c$)$length and depth to the nearest $2\mathrm{.}5$ cm

d$)$length and depth to the nearest $15$ cm

$38)$what data must be recorded for a townhouse that has $3$ room air conditioner window units and one room air conditioner single$-$hose portable unit?

a$)$the total number of air conditioner units

b$)$the SEER rating of the window units only

c$)$the manufacturer and model number of the window units only

d$)$the manufacturer, model number and SEER rating of the portable unit only

$39)$in a house where an attached garage provides heated storage for up to $6$ vehicles, how would an energy advisor assess the floor of living area located immediatly above this parking garage

a$)$floor header

b$)$exposed floor

c$)$floor above frostline

d$)$ floor ablve foundation

$40)$ during the process of the constrion blower door service, which of the following steps is required when a builder aims to meet a specific airtighness target?

a$)$tape intentional openings

b$)$perform a duct leakage test

c$)$conduct an exhaust devices depressurization test

d$)$have the builder seal air leaage points

$41)$actual blower door test results are modelled in the "air leakage test data" tap of HOT$2000,$ why does this fail the requirement of a valid test?

a$)$the relative error is too high

b$)$there is a data point with too much error

c$)$the flow exponent is outside the allowable range

d$)$the correction coefficient is outside the allowable range

$42)$how would tank type be modelled in HOT$2000$ for the domestic hot water system shown below?

a$)$conventional tank

b$)$instantaneous

c$)$induced draft

d$)$direct vent

$43)$which of the fllowing is the most appropriate course of action when providing info regarding an insulation contractor?

a$)$providing the homeowner with business cards from $3$ local insulation contractors

b$)$informing the homeowner of insulation contractors that are personally known by the energy advisor

c$)$referring the homeowner to the publication entitled get it in writing

d$)$making arrangements for a salesperson from your service organization or an affiliated company that provides insulation contact the homeowner with a quote

$44)$ if vermiculite insulation is exposed to the interior environment how should an energy advisor proceed?

a$)$collect a sample and submit it for asbestos analysis

b$)$document its presence and proceed with the airtighness test

c$)$continue with the evaluation but do not perform an airtighness test

d$)$report to the homeowner that the insulation should be removed and disposed of

$45)$if vermiculite is observed in an enclosed space $($atttic or wall$)$ and is not exposed to the interior environment what procedure should be followed?

a$)$refrain from performing an air tightness test

b$)$advise the homeowner to have the vermiculite removed

c$)$ignore the vermiculite and do not mention it to the homeowner

d$)$provide a hard copy of the document health risk asbestos or a link to the web page