Question: [ 6 ] ( 1 5 points ) Given the state of the stress below, determine ( 1 ) the principal stresses and the maximum

[6](15 points) Given the state of the stress below, determine
(1) the principal stresses and the maximum in-plane shear stress at the point;
(2) the stress components acting on the inclined plane AB.
Using Mohr's cincle
[ 6 ] ( 1 5 points ) Given the state of the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

P 3 Ans: ( a ) 1 0 . 5 3 3 MPa, 2 5 . 1 2 5 MPa, - 4 . 0 1 4 MPa, ( b ) 2 6 . 2 MPa, 9 . 5 0 MPa; 8 . 3 3 MPa; 1 7 . 8 3 MPa; 1 3 . 0 8 MPa; ( c ) 2 . 2 9 , 2 . 1 , ( d ) 2 . 2 9 A pressurized pipe...

Q:

For the state of stress with x = 50ksi (compression), y = 100ksi (compression), T = 25ksi (down on the right face) draw Mohr's circle and identify the axes, average stress, principal stresses,...

Q:

5. (5) Consider the thin-walled pressure vessel below with internal gage pressure p, mean diameter d, and thickness t. CI. d X a. Determine (in terms of p, d, and t) the stresses on the x y element...

Q:

Problem 3 = A force P of 80 kN is applied in the plane xy to the beam show on the figure. The material has a Young's modulus E 200 GPa and a Poisson's ration v = 0.3. DO NOT CONSIDER THE CRACK FOR a)...

Q:

A solid cylindrical shaft with a diameter of 9 0 mm is subjected to a bending moment of 1 0 0 0 Nm and a torque of 8 0 0 Nm . Calculate the principal stresses, maximum shear stress, and von Mises...

Q:

3. Mohr's circle is shown in the Figure for a point in a physical object that is subjected to plane stress. a) Determine the stresses Ox, Oy, and Txy and show them on a stress element. b) Determine...

Q:

For the simple state of pure shear (or torsion), Txy = to and all other stresses are 0. a. Draw the xy element b. Sketch Mohr's circle, in terms of to. c. Determine principal stresses (in terms of...

Q:

The state of plane stresses at a point in a member is shown on the element in Figure Q5. 70 MPa 15 MPa T Figure Q5 50 MPa i) Sketch a Mohr's circle for the plane stresses. ii) Determine the principal...

Q:

Mohr's circle is shown in the Figure for a point in a physical object that is subjected to plane stress. a ) Determine the stresses x , y , and x y and show them on a stress element. b ) Determine...

Q:

A hollow cylindrical shaft with an outer diameter of 1 0 0 mm and an inner diameter of 8 0 mm is subjected to a bending moment of 1 2 0 0 Nm and a torque of 1 0 0 0 Nm . Determine the principal...

Q:

In 2010, Josh Johnson of the Florida Marlins had the lowest earned-run average (ERA is the mean number of runs yielded per nine innings pitched) of any starting pitcher in the National League, with...

Q:

In Figure an x-ray beam of wavelengths from 95.0 to 140 pm is incident at 0 = 45.0o to a family of reflecting planes with spacing d - 275 pm. What are the (a) Longest wavelength I and (b) Associated...

Q:

On January 1 , 2 0 2 3 , Riverbed Corporation, which follows IFRS, issued a series of 5 0 1 convertible bonds, maturing in five years. The face amount of each bond was \ ( \ $ 1 , 0 0 0 \ ) ....

Q:

The following excerpt comes from the introduction of a book Executive Compensation: Accounting and Economic Issues, written by Gary Giroux in 2014. By using concepts studied in class, please explain...