Question: 6 . For the welded joint shown in Fig . 6 . Find the maximum force per mm of the weld. ( Ans . 6

6. For the welded joint shown in Fig.6. Find the maximum force per mm of the weld. (Ans.620 N/mm)
Fig.6.
(All Dimensions in MM)
6 . For the welded joint shown in Fig . 6 . Find

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

2 1 . A plate 1 m long, 6 0 mm thick is welded to another plate at right angles to each other by 1 5 mm fillet weld, as shown in Figure below. Find the maximum torque that the welded joint can...

Q:

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

Q:

Each arm comprises a horizontal beam made from an AISI651 stainless steel tube (see Table 1 for the material properties) of length L = 35 mm, inner diameter d = 375 m and outer diameter do = 575 m,...

Q:

What are the reasons of replacing riveted joint by welded joint in modern equipments?. A welded joint as shown in Fig., is subjected to an eccentric load of 2 kN. Find the size of weld, if the...

Q:

What are the reasons of replacing riveted joint by welded joint in modern equipments?. A welded joint as shown in Fig., is subjected to an eccentric load of 2 kN. Find the size of weld, if the...

Q:

What are the disadvantages of welded joint? Explain in details. A 50 mm diameter solid shaft is welded to a flat plate as shown in Fig. If the size of the weld is 15 mm, find the maximum normal and...

Q:

Consider the following drawing in which plate 1 is welded onto plate 2 as shown for tensile and shear loading. The plates are fillet welded with a weld thickness of 6 mm as shown for a length of 1 5...

Q:

the impedence values in question 4 is j0.25 and the reactance is 0.5 10 10 6 1. For the system data given below draw the single line diagram. Represent the power, voltage and impedances in per units...

Q:

6. 7. 8. The lengths of various links of a mechanism, as shown in Fig. 6.32, are: OA = 0.3 m ; AB= 1 m; CD=0.8 m; and A C= CB. Determine, for the given configuration, the velocity of the slider D if...

Q:

A metal pipe that has a wall thickness of 1 2 mm and an outer diameter of 4 2 0 mm is made by welding sections together along an inclined joint at an angle of 2 2 degrees from the axis perpendicular...

Q:

Martin purchased 80% of Lewis for $750,000 on January 1, 20x1. Martin's excess of cost over book value was $10,000. The excess due to undervalued equipment is to be amortized over four years. During...

Q:

Let (J,) be the partially ordered set with J = {0, 1} and with 0

Q:

4 5 0 - 2 0 - 2 5 - 2 An estimated loss from a loss contingency shall be accrued by a charge to income if both of the following conditions are met: a Information available before the financial...

Q:

of 15 Direct labor: 4 hours at $13 per hour Variable overhead:4 hours at $5 per hour Total standard variable cost per unit Thecompany also established the following cost formulas for itsselling exp 2...