Question: A beam having the cross-section shown below is subjected to a bending moment of 1500 Nm in x-axis. Calculate the maximum direct stress due

A beam having the cross-section shown below is subjected to a bending moment of 1500 Nm in x-axis. Calculate the maximum dire

A beam having the cross-section shown below is subjected to a bending moment of 1500 Nm in x-axis. Calculate the maximum direct stress due to bending and state the point at which it acts. 40mm 80 mm 8 mm 80 mm 8 mm E

Step by Step Solution

★★★★★

3.56 Rating (163 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

A3 A Rwan Ap Saxe 640 02 A 1200x89600m Ixx 120mm A2 A 80x8 640mm A 80x8 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

The curved beam is subjected to a bending moment of M = 85 N · m as shown. Determine the stress at points A and B and show the stress on a volume element located at these points. M = 85 N-m...

A welded steel girder having the cross section shown in the figure is fabricated of two 300mm x 25mm flange plates and a 800mm x 16mm web plate. The plates are joined by four fillet welds that run...

A welded steel girder having the cross section shown in the figure is fabricated of two 20in x 1 in. flange plates and a 60in x 5/16in. web plate. The plates are joined by four longitudinal fillet...

Determine the plastic moment MP for a beam having the cross section shown in the figure if ÏY = 210 MPa. 120 150 250 mm 30 mm

The concrete bridge pier, shown in the photo, supports a portion of a highway bridge. The centerline dimensions and the anticipated loading on the cap or top beam are shown in the figure. This beam...

The internal shear force V at a certain section of an aluminum beam is 12.8 kN. If the beam has the cross section shown (assume a=28 mm, bf=76 mm, tw=t,=6 mm, d=87 mm), determine: (a) the shear...

Consider the non-prismatic cantilever beam of circular cross section shown. The beam has an internal cylindrical hole in segment 1; the bar is solid (radius r) in segment 2. The beam is loaded by a...

A simple beam that is 18 ft long supports a uniform load of intensity q. The beam is constructed of two C 8 x 11.5 sections (channel sections or C shapes) on either side of a 4 x 8 (actual...

A simple beam that is 18 ft long supports a uniform load of intensity q. The beam is constructed of two angle sections, each L 6 x 4 x 1/2, on either side of a 2 in. x 8 in. (actual dimensions) wood...

Determine the plastic moment M p that can be supported by a beam having the cross section shown. Ï Y = 30 ksi. 2 in. -1 in. M, 10 in. K1 in.

Why is a note receivable sometimes preferred to an account receivable?

Answer the questions below in the form of a paragraph: If you were working in audience data collection, how would you approach tensions relating to data collection methods that comes at the expense...

Find a formuls for the inverse of the function. g ( x ) = 3 x 4 2 g - 1 ( x ) =

let Y=TR with the kpology Ty={VCR: R-QC}Ure let A= (R-Q)x (GQ). consider the product topologyon XxY. Find Int CA), Bel(A). ExtcA), A'

let Y=TR with the kpology Ty={VCR: R-QCU}Ure let A= (R-Q)x (GQ). consider the product topologyon XxY. Find Int CA), Bel(A). ExtcA), A'

Start with the partial model in the file attached. Marvel Pence, CEO of Marvels Renovations, a custom building and repair company, is preparing documentation for a line of credit request from his...

Use the Laplace transform method to evaluate the following convolution integral: e^(-t)*sin(t)

The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Determine the average normal strain in each wire. The wires are...

The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the top and bottom distribute the load uniformly throughout the block, determine the average normal...

Determine the resultant internal loadings on the cross section at point D. 1.25 kN/m 1.5 m '0.5 m' 0.5 m'0.5 m

A $30,000 loan at 6.7% compounded annually requires monthly payments of $450. a. Calculate the interest component of Payment 29. b. Calculate the principal component of Payment 65. c. Calculate the...

Cloverdale Nurseries obtained a $60,000 loan at 7.5% compounded monthly to build an additional greenhouse. Monthly payments were calculated to amortize the loan over six years. Construct a partial...

Will a loans balance midway through its amortization period be (pick one): (i) More than (ii) Less than or (iii) Equal to half of the original principal? Explain.