Question: A bolt is designed to take up direct tensile load of 3 0 kN and a shear load of 1 6 kN with a factor

A bolt is designed to take up direct tensile load of 30 kN and a shear load of 16 kN with a factor of safety of 4. The yield strength of the material used is 400 MPa. Calculate the size of the bolt based on various theories of failure. Take =0.3.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

harp Screen Films, Inc., is developing its annual financial statements at December 31, current year. The statements are complete except for the statement of cash flows. The completed comparative...

Q:

Question 1 The frame supports the point load P at point C. The pins at A and B have diameters of 50 mm and 64 mm respectively. Pin A is in single shear, while Pin B is in double shear, and both pins...

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A bolt with tensile stress area = 1 0 0 m * m ^ 2 is used to connect two parts ( made of same materials as that of the bolt with S _ { a } = 6 0 0 MPa, S _ { y } = 5 0 0 MPa and the corrected...

Q:

A cylindrical pressure vessel with an inner radius of 0 . 4 meters and a wall thickness of 1 2 mm is subjected to an internal pressure of 5 MPa. Determine the hoop stress and longitudinal stress in...

Q:

A cylindrical pressure vessel with an inner radius of 0 . 4 meters and a wall thickness of 1 2 mm is subjected to an internal pressure of 5 MPa. Determine the hoop stress and longitudinal stress in...

Q:

( 3 pts ) Strain. A short compression member 3 in , by 3 in . in cross - section and 1 4 in . long is subjected to a 6 0 , 0 0 0 l b axial compressive load. As a result, the length of the member is...

Q:

A solid cylindrical shaft with a diameter of 9 0 mm is subjected to a bending moment of 1 0 0 0 Nm and a torque of 8 0 0 Nm . Calculate the principal stresses, maximum shear stress, and von Mises...

Q:

A solid cylindrical shaft with a diameter of 4 5 mm is subjected to a bending moment of 5 0 0 Nm and a torque of 4 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on...

Q:

Construct a finite-state machine for the log-on procedure for a computer, where the user logs on by entering a user identification number, which is considered to be a single input, and then a...

Q:

Four types of checking accounts are offered by one bank. Suppose that recently a random sample of 300 bank customers was surveyed and asked several questions. It was found that 60% of the respondents...

Q:

USE THE SESSION DATE AS 0 1 / 3 1 / 2 0 2 3 1 . Enter the following vendor historical invoices. Al l taxes on these invoices should be 0 . 0 0 . Use 0 1 / 3 1 / 2 0 2 3 as the batch date....

Q:

. Question 12 (25 points) Saved The Assembly Department of Fast Motors operates a Weighted Average process-costing system in which all direct materials are added at the beginning of the process and...