Question: A continuous beam carries a distributed load and concentrated load as shown in the figure. Solve the following question below when P160kN and w=115 kN/m

A continuous beam carries a distributed load and concentrated load as shown in the figure. Solve the following question below when P160kN and w=115 kN/m

what is the first TME factor of the span CD?

Solve the moment at point B?

Solve the moment at point C?

Step by Step Solution

★★★★★

3.40 Rating (153 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

A shock mount constructed as shown in the figure is used to support a delicate instrument. The mount consists of an outer steel tube with inside diameter b, a central steel bar of diameter d that...

The tapered cantilever beam AB shown in the figure has thin-walled, hollow circular cross sections of constant thickness t. The diameters at the ends A and B are dA and dB = 2dA, respectively. Thus,...

The horizontal beam ABC shown in the figure is supported by column BD and CE. The beam is prevented from moving horizontally by the pin support at end A. Each column is pinned at its upper end to the...

A cantilever beam AB carries three equally spaced concentrated loads, as shown in the figure. Obtain formulas for the angle of rotation Î¸B and deflection Î´B at the free end...

Points (a, b) and (c, d), not shown in the figure above, are in quadrants I and III, respectively. If abcd 0, then the point (bd, bc) must be in which quadrant? I II III IV It cannot be determined...

Consider a simply supported beam shown in the figure. Solve the problem using plane stress solids. Perform a convergence study for displacement at the center and maximum tensile stress. Increase the...

The simple beam AB is subjected to a uniform distribution load as shown in the figure. Draw a shear force plot and find the position and value at which the shear force magnitude is maximized. A W L B

1. Four charges are of values and at positions as shown in the figure below. In this problem we will be considering the force that three of the charge exert on the fourth. a. Find the x and y...

A 50-lossless line is terminated in a load impedance ZL = (30 - j20). (a) Calculate and S. (b) It has been proposed that by placing an appropriately selected resistor across...

A plane truss is subjected to loads 2P and P at joints B and C, respectively, as shown in the figure part (a). The truss bars are made of two L102 Ã 76 Ã 6.4 steel angles [see Table...

Again, I'm honestly not certain this course did much to address/improve my decision making abilities. The early exercises did generate some awareness of items I could keep in mind while making...

Define and explain two of the four pieces to Lessig's Framework. I should see how you understand how Lessig's Laws apply to the IT world. (Minimum of two paragraphs)Thank you

Explain in detail the different methods of performance appraisal .

In a particular county, the average number of suicides reported each month is 2.75. Assume that the number of suicides follows a Poisson distribution. What is the probability that at least two (two...

Renaldo's Bakery makes bread for the local restaurants. Gennaro's job is to inspect the bread for defects, including size, holes, slice width, hardness, and softness. Each loaf of bread could have as...

could i get this question refunded i do not need it anymore Required information Problem 05-4A Break-even analysis; income targeting and forecasting LO C2, P2, A1 The following information applies to...

One Way Cellular accountants have assembled the following data for the year ended September 30, 2014: Prepare the operating activities section using the indirect method for One Way Cellulars...

A composite beam consisting of fiberglass faces and a core of particle board has the cross section shown in the figure. The width of the beam is 2.0 in., the thickness of the faces is 0.10 in., and...

A compound beam ABCDE (see figure) consists of two parts (ABC and CDE) connected by a hinge (i.e., moment release) at C. The elastic support at B has stiffness k = EI/b3 Determine the deflection...

The beam ABC shown in the figure is simply supported at A and B and has an overhang from B to C. The loads consist of a horizontal force P1 = 4.0 kN acting at the end of a vertical arm and a vertical...

Calculate the estimate for the given data. b. Use rules of variance from Chapter 5 to obtain an expression for the variance and standard deviation (standard error) of the estimator in part (a), and...

Using a long rod that has length , you are going to lay out a square plot in which the length of each side is . Thus the area of the plot will be 2 . However, you do not know the value of , so you...

Each of 150 newly manufactured items is examined and the number of scratches per item is recorded (the items are supposed to be free of scratches), yielding the following data: Number of scratches...