Question: A half - wave rectifier, as in circuit below ( from TB ) , is used to provide a DC supply to a 1 0

A half-wave rectifier, as in circuit below (from TB), is used to provide a DC supply to a 100- load. If the AC voltage source is 20 V rms , find the peak and average current in the load. Assume an ideal diode.
A half - wave rectifier, as in circuit below (

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Q:

Computer science!!! 2. Single phase half wave circuit with R-L load Vesna 11. Output current i, rises gradually. After some time i, reaches a maximum value and then begins to decrease. At , Vo =0 but...

Q:

The purpose of a rectifier to produce an output that is DC, or the purpose may be to produce a voltage or current wave-form that has a specified DC component. In practice, the half-wave rectifier is...

Q:

The full wave rectifier function is to produce a voltage or current that is purely DC or has some specified DC component. The output of the full wave rectifier has inherently less ripple than the...

Q:

Fig. 5 presents a half wave rectifier. We assume Vin here is sinusoidal, with 2V peak-to-peak, no DC offset. Draw the Vout waveform when the diode has 0.7V voltage drop. Diode AC Voltage Source Vin...

Q:

1. Using stress-strain diagrams, show the difference in deformation response between elastic and linear viscous (newtonian) materials. Label your diagrams 31. List three types of material objects...

Q:

1. Define organization Behavior. 2. List the types of personality. 3. Difference between emotional intelligence and emotional Labour. 4. What do you understand by group dynamics? 5. Define...

Q:

Design and draw a power supply circuit that converts a 2 2 0 Vrms 5 0 Hz to + 1 2 V and - 1 2 DC , with a ripple voltage less than 5 0 mV , the maximum load current that will be drawn by the load...

Q:

A 200-V, 3-A dc power supply is to be designed with less than a 2 percent ripple voltage. Compare the pros and cons of implementing this power sup- ply with half-wave, full-wave, and full-wave bridge...

Q:

1 4 - Single phase half bridge inverters requires a ) two wire ac supply b ) two wire de supply c ) three wire ac supply d ) three wire dc supply 1 5 . Find the average value of output current of a...

Q:

2.a) Explain about various current components in a forward biased p-n junction diode. b) With neat sketches and necessary waveforms explain about the regulation characteristics OR 3.a) With neat...

Q:

Repeat Worked-Out Problem 19.1, but assume instead that Joe and Rebecca both have a marginal cost of $55 per cubic yard. What is the deadweight loss in this market?

Q:

Michael Carrigg, Inc., is disk manufacturer in need of an aggregate plan for July through December. The company has gathered the following data: Costs________________ Holding cost ...........

Q:

4 Work out each subtraction. Some working has been shown to help you. 1 1 1x7-1x2 7-2, a 2 7 C 27 2x7 3x7-2x5 = b 14 14 35 d 5 7 5x7 35 35 2 23 1 2x5-1x3 5 = 3x5 5 3 5x5-3x6 65 6x5 15 15

Q:

If $2000 is invested at 5% simple interest, the initial value and the future value S at the end of each of 5 years is shown in the table below. Then answer part (a) through (d). Year (t) Future Value...