Question: A stepper motor controls a linear slider with a ball screw. The pitch of the screw is 8mm and the step of the motor

A stepper motor controls a linear slider with a ball screw. The pitch of the screw is 8mm and the step of the

A stepper motor controls a linear slider with a ball screw. The pitch of the screw is 8mm and the step of the motor is 1.80 per pulse. There 20000 pulses to move the slider 0.8m.The frequency of the step pulse is 4.7 kHz What is the speed of the slider in meters per second?

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The problem statement gives the following information about the stepper motor system The pitch of the screw is 8 mm which means for each full rotation ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

Exercise 1 0 - 1 5 A ( Algo ) Straight - line amortization of a bond premium LO 1 0 - 5 The Square Foot Grill, Incorporated issued $ 2 0 3 , 0 0 0 of 1 0 - year, 9 percent bonds on January 1 , Year 2...

The shaft of a stepper motor is directly connected to a lead screw that drives a worktable in an x-y positioning system. The motor has a step angle = 5(. The pitch of the lead screw is 6 mm, which...

Consider the following statement: The essence of project management is risk management. What does it mean in terms of completing a project successfully? Support your response with evidence from the...

1 . - NC Open - Loop Positioning The worktable of a positioning system is driven by a ball screw whose pitch = 5 . 0 m m . The screw is connected to the output shaft of a stepper motor through a...

The worktable of a positioning system is driven by a ball screw whose pitch = 8.0 mm. The screw is connected to the output shaft of a stepper motor through a gearbox whose ratio is 6:1 (six turns of...

1. The worktable of a positioning system is driven by a ball screw whose pitch = 8.0 mm. The screw is connected to the output shaft of a stepper motor through a gearbox whose ratio is 6:1 (six turns...

The worktable of a positioning system is driven by a ball screw whose pitch = 1 0 . 0 mm . The screw is connected to the output shaft of a stepper motor through a gearbox whose ratio is 8 : 1 ( eight...

6.The worktable of a positioning system is driven by a ball screw whose pitch = 10.0 mm. The screw is connected to the output shaft of a stepper motor through a gearbox whose ratio is 8:1 (eight...

1. The worktable of a positioning system is driven by a ball screw whose pitch = 10.0 mm. The screw is connected to the output shaft of a stepper motor through a gearbox whose ratio is 8:1 (eight...

One axis of the worktable in a CNC positioning system is driven by a ball screw with a 6 - mm pitch. The screw is powered by a stepper motor which has 1 8 0 step angles using a 2 : 1 gear reduction (...

In October, Nicole eliminated all existing inventory of cosmetic items. The trouble of ordering and tracking each product line had exceeded the profits earned. In December, a supplier asked her to...

Obtain Bode plots for both the transfer function given as follows and a FOPTD approximation obtained using the method discussed in Section 6.3. What do you conclude about the accuracy of the...

9 of 2 0 An individual who's MOST concerned with a potential loss on an investment will have a primary investment objective of: Liquidity B Preservation of capital C Growth D Capital reserve

Consider the system shown in Figure P10.44 with m 1 = 20.0kg, m 2 = 12.5kg, R=0.200 m, and the mass of the uniform pulley M=5.00kg. Object m 2 is resting on the floor, and object m 1 is 4.00 m above...

Prove that similarities form a group.

Construct a 3-bit counter using three D flip-flops and a selection of gates. The inputs should consist of a signal that resets the counter to 0, called reset, and a signal to increment the counter,...

Calculate the change in enthalpy for the following specific rxn. Be sure to indicate the correct sign (- or +) for the change in enthalpy: Mg(s) + 2H + (aq) --> Mg 2+ (aq) + H 2 (g) This is for a...

A steel pipeline, 2-in, schedule 40 pipe, contains saturated steam at 121.1C. The line is covered with 25.4 mm of insulation. Assuming that the inside surface temperature of the metal wall is at...

During the first week of his new job as a sales rep for a national auto parts distributor Tyler attended a regional sales conference he couldn't help but noticed that the 400 sales reps there nearly...

In previous problem 20.4, the design specification on the part is that the critical cross-sectional dimension = 28.0 ( 2.0 mm. (a) What proportion of parts fall outside the tolerance limits? (b) If...

The worktable of an NC machine is driven by a closed-loop positioning system which consists of a servomotor, Leadscrew, and optical encoder. The lead screw pitch = 4 mm and is coupled directly to the...

An automated system consists of what three basic elements.

Identify some biological bases of personality.

7.4. When a recent Eurobarometer survey asked subjectsin each European Union country whetherthey would be willing to pay more for energy produced from renewable sources than for energy produced from...

Identify the advantages and disadvantages of using interviews, behavioral assessments, and personality inventories to measure personality.