Question: A turning operation is performed on a cylindrical work part whose diameter = 150 mm and length = 500 mm. Cutting speed = 3.0 m/s,

A turning operation is performed on a cylindrical work part whose diameter = 150 mm and length = 500 mm. Cutting speed = 3.0 m/s, feed = 0.3 mm/rev, and depth of cut = 2 mm. Determine: a. the cutting time and, b. the material removal rate

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

A 250-mm-wide strip with a thickness of 20 mm is fed through a rolling mill with two powered rolls, each of radius = 200 mm. The work thickness is to be reduced to 17 mm in one pass at a roll speed...

A turning operation is to be performed on an NC lathe. Cutting speed = 2.5 m/s, feed = 0.2 mm/rev, and depth = 4.0 mm. Work piece diameter = 100 mm and its length = 400 mm. Determine (a) Rotational...

Q1) Determine the cutting force and feed (thrust) force for a turning operation using the following parameters: Material tensile strength 250MPa, Shear strength 120 MPa, chip thickness ratio r =...

. 54. ABC, a domestic corporation, 60% Filipino owned, had the following gross receipts from world championship events it conducted in the Philippines: Billiards (between Bata Reyes & Don Ming S...

Choose the correct answer only, no explanation is needed. Abdul Company is engaged in a variety of businesses around south. The CEO thought of expanding and the way to do that is to buy a portion or...

So far, we have discussed identifying and recording/analyzing transactions. From there, we would post journal entries to the general ledger and made an unadjusted trial balance. From there, we would...

Problem A turning operation is performed on a lathe to reduce the diameter of a part. The initial diameter of the part is 5 0 mm , and the final diameter is 4 8 mm . The length of the cut is 1 0 cm ,...

2 0 . 5 ( A ) ( USCS units ) A turning operation is performed using a rake angle of 1 5 . Cutting speed = 2 0 0 f t m i n , feed = 0 . 0 1 2 i n r e v , and depth of cut = 0 . 1 0 0 i n . The chip...

Use R to this task The original roulette table randomly selects a number from 0-36 and attaches a color to each of these number (Red, Black, and Green). Gamblers can place a bet on any red or black...

The following questions are related to the worksheet named "jDPower" Develop a frequency distribution of the overall mechanical quality ratings. Describe the distribution. S JDPower Develop a...

Do you believe it is ethical for companies to compile portfolios of personal information about their website visitors without informing them? What about organizations monitoring their employees use...

(10%) Problem 4: A rectangular loop with L, -0.15 m and L-0.65 m is sitting in a magnetic field B-0.75 T as shown in the figure. There is a counterclockwise current / - 0.45 A in the loop. Calculate...

Construct an annual incremental operating cash flow statements for the next 4 years, using the following: Four - Year Sales Description Year 1 Year 2 Year 3 Year 4 Units 1 , 5 0 0 1 , 5 7 5 1 , 6 0 5...

Someone who saves a person from drowning in the hopes of being paid for it is acting morally? why or why not?

Review the information in Figure 61 in the book entitled Nursing Informatics and the Foundation of Knowledge. Develop a clinical question related to your area of practice that you would like to...

Find all distinct eigenvalues of A. Then find a basis for the eigenspace of A corresponding to each eigenvalue. For each eigenvalue, specify the dimension of the eigenspace corresponding to that...

The definition of a terrorist is someone who commits acts of violence to communicate a message. Would you classify the UNAbomber as a terrorist? Explain

6 Theory of Machines 5. A shaft carries five masses A, B, C, D and E which revolve at the same radius in planes which are equidistant from one another. The magnitude of the masses in planes A, C and...

Use the extended bottleneck model to solve problem 19.2 with the following number of parts in the system: (a) N = 3 parts and (b) N = 6 parts. Also determine the manufacturing lead time for the two...

A production line consists of six workstations, as shown in the accompanying figure. The six stations are as follows: (1) First manufacturing process, scrap rate is q1 = 0.10; (2) Inspection for...

Name three of the four conditions under which automated production lines are appropriate.

What does the symbol n represent in the statement X ~ b(n, p)?

Telephone survey. Exercise 6.5 introduced a random digit dialing machine with p = 0.15 for each call attempt. (a) What is the expected value and variance for the number of contacts in eight attempts?...

Tay-Sachs couples. Approximately 1 in 28 people of Ashkenazi Jewish descent are Tay-Sachs carriers. In randomly sampling one man and one woman from this population, what is the probability neither is...