Question: An axial load is applied to a square post shown in the figure. The shear stress on section AB was found to be 30MPa.

An axial load is applied to a square post shown in the figure. The shear stress on section AB was found to be 30MPa. Determine the average normal stress acting on section AB. 350 P

Step by Step Solution

★★★★★

3.46 Rating (159 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Solutions 30 HImm 6 11 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

The steel plane truss shown in the figure is loaded by three forces P, each of which is 490 kN. The truss members each have a cross-sectional area of 3900 mm2 and are connected by pins each with a...

A schematic of a clutch-testing machine is shown. The steel shaft rotates at a constant speed . An axial load is applied to the shaft and is cycled from zero to P. The torque T induced by the clutch...

PROBLEMS For the following problems, unless noted otherwise, refer to Appendices F and/or G for necessary mechanical prop- erties. Section 4-1 Poisson's Ratio A 1. A 2 in. diameter AISI 1020 steel...

Answer two independent questions a. The Company has budgeted the following activity for April: Sales of $1,000,000 all in cash . The cost of goods sold is 75% of the selling price Inventory purchases...

Final Name Surname: Student iD 2 0 2 2 - 2 0 2 3 Fall Semester - Duration: 1 0 0 minutes Course Nathe : cvin 2 2 2 - Mechanics of Mroup: . . . . . Date! ( 3 0 9 5 ) A WT 2 0 5 3 0 structural steel...

4 . A post with a solid circular cross section supports a load applied on a plane parallel to the yz - plane. The load is at an angle of \ ( 3 0 ^ { \ circ } \ ) from a line parallel to y axis as...

In what way do legal systems have an impact on global business?

Problem C - 2 [ Average Normal and Average Shear Stresses ] As shown in the figure, member A B and member B C are connected through a pin joint at B ( i . e . , double shear ) ; The other ends of the...

Marks ) : Determine the largest load P that can be applied on the frame shown in Figure ( 1 ) without causing either the average normal stress or the average shear stress at section aa to exceed \ (...

A tensile member in a machine structure Torsion Compute the torsional shear stress in a circular shaft with a diameter of 5 0 mm that is subjected to a torque of 8 0 0 N - m . Compute the torsional...

The graph provides data on the numbers of bachelors degrees conferred on men and on women in selected years. How many more bachelors degrees were conferred on women in 2010 than in 1970?

Obtain the inverse Laplace transform x(t) for each of the following transforms: a. X(s) = (7s + 2)/(s2 + 6s + 34) b. (4s + 3)/(s(s2 + 6s + 34) c. X(s) = (4s+9)/((s2+6s+34)(s2+4s+20)) d. X(s) = (5s2 +...

A company is developing a new game for a hand-held console: The console is moved in various directions to control movement and speed of a racing car on a television screen. Gear changes can be done...

A circular disk with a radius of ( 8.70 + 0.05) cm and a thickness of (0.480 0.005) cm. Find the the uncertainty in the volume in cubic centimeter. (Your result must include proper number of digit...

The 4.00-kg block in the figure (Figure 1)is attached to a vertical rod by means of two strings. When the system rotates about the axis of the rod, the strings are extended as shown in the diagram...

handwrite was not clear l need basic solution and cleary visible please The 4.00-kg block in the figure (Figure 1)is attached to a vertical rod by means of two strings. When the system rotates about...

there is 3 different answer on this site 3 different pls if you not sure dont answer A 28Bkg i; to 2D&kg by cully (Fig _ 473). of static frict& table b I uk is aefficient of table block iz is...

Two parallel conducting plates are separated by 10.0 cm, and one of them is taken to be at zero volts. (a) what is the electric field strength between them, if the potential 8.00 cm from the zero...

Saralis Corporation had the following balances at December 3 1 , Year 2 : \ table [ [ Property , plank, and equipment,$ 1 , 7 5 7 , 0 0 0 , Goodwil,$ 2 9 6 , 8 0 0 ] , [ Interest payable, 8 , 4 5 0 ,...

Repeat Prob. 620 but with an alternating torsional stress of 15 kpsi and a steady bending stress of 15 kpsi. Repeat Prob. 620, A bar of steel has the minimum properties Se = 40 kpsi, Sy = 60 kpsi,...

The hub diameter and projection for the gear of Prob. 1351 are 100 and 37.5 mm, respectively. The face width of the gear is 50 mm. Locate bearings C and D on opposite sides, spacing C 10 mm from the...

The cantilevered handle in Prob. 384 is made from mild steel. Let Fy = 250 lbf and Fx = Fz = 0. Using Castiglianos theorem, determine the vertical deflection (along the y axis) at the tip. Repeat the...

a-c. Consider the accompanying computer results, which describe regression analyses involving two independent variables X1 and X2 and a dependent variable Y (using a different data set from the one...

Use the computer output from Problem 10 in Chapter 8 and from Problem 16 in Chapter 5 to answer the following questions. (Assume that no interaction occurs between house size [X1] and number of rooms...

Consider the following computer results, which describe regression analyses involving two independent variables X1 and X2 and a dependent variable Y. Assume that your goal is to assess the...