Irrigation and Drainage Civil engineering 4. An irrigation project is planned in an arid zone. The maximum
Fantastic news! We've Found the answer you've been seeking!
Question:
Irrigation and Drainage
Civil engineering
Transcribed Image Text:
4. An irrigation project is planned in an arid zone. The maximum water requirements of crops are estimated in August during which no precipitation is observed. The mean river discharge is 15 m/s. Of this amount, Qr discharge is diverted to irrigate the project area as shown in Figure 1. The areal distribution of crops k values to be used in the Blaney-Criddle equation are given below for August with t-30°C. Take overall eficiency E-60%. The area is located on 38° latitudes in northern hemisphere. a) Determine the design irrigation discharge of the project area (Qir) b) Determine the section dimensions of the trapezoidal main canal at point A with Som 0.0008, z=1.5, n= 0.016 and b = 1.8 m. Consider umin= 0.5 m/s. Q-15 m/s IRRIGATION AREA 4000 ha Figure 1. Definition sketch for problem 4. 4. An irrigation project is planned in an arid zone. The maximum water requirements of crops are estimated in August during which no precipitation is observed. The mean river discharge is 15 m/s. Of this amount, Qr discharge is diverted to irrigate the project area as shown in Figure 1. The areal distribution of crops k values to be used in the Blaney-Criddle equation are given below for August with t-30°C. Take overall eficiency E-60%. The area is located on 38° latitudes in northern hemisphere. a) Determine the design irrigation discharge of the project area (Qir) b) Determine the section dimensions of the trapezoidal main canal at point A with Som 0.0008, z=1.5, n= 0.016 and b = 1.8 m. Consider umin= 0.5 m/s. Q-15 m/s IRRIGATION AREA 4000 ha Figure 1. Definition sketch for problem 4.
Expert Answer:
Answer rating: 100% (QA)
a Taxable income 31560 Tax rate was 9275 plus 15 over 9275 Total ... View the full answer
Related Book For
Automation Production Systems and Computer Integrated Manufacturing
ISBN: 978-0132393218
3rd edition
Authors: Mikell P.Groover
Posted Date:
Students also viewed these accounting questions
-
(a) A beam as shown in Figure 1 is subjected to a point load of P kN at point B and a concentrated moment of M kNm at point E. Flexural rigidity for spans AC and CE are 2EI and EI, respectively....
-
First environment as shown in Figure 1 The air with r 1 = 1 and the second environment is r 2 = 3 Packed with a material. Electrical flux density in the first medium vector of D1 = 6ax 1.5ay + 3az...
-
This figure shows an estimated linear equation with 95% prediction intervals. Assume that the units of X and Y are dollars. (a) Visually estimate the intercept b0 and the slope b1. (b) Is se (b1)...
-
From the work sheet, prepare the following: 1. Closing entries for Gimbel's Gifts and Gadgets in a general journal. 2. A post-closing trialbalance. Gimbel's Gifts and Gadgets Work Sheet For Year...
-
What is the difference between fixed cost and variable cost? Does each type of cost affect short-run marginal cost? If yes, explain how each affects marginal cost. If no, explain why each does or...
-
Predict which atom will have the highest magnitude of EA, As or Br.
-
Excess Gibbs free energy models are used to determine the value of the (a) Isothermal compressibility (c) Coefficient of volume expansion (b) Activity coefficient (d) Gibbs' free energy.
-
You have the following information for Vincent Inc. for the month ended October 31, 2014. Vincent uses a periodic method for inventory. Instructions (a) Calculate (i) ending inventory , (ii) cost of...
-
The information necessary for preparing the December 31, 2021 year-end adjusting entries for Tonic Salon and Spa appears below. Tonic's fiscal year-end is December 31. a. On July 1, 2021, Tonic...
-
Complete Form 941 for the 4th quarter for TCLH Industries (which is located at 202 Whitmore Avenue, Durham, NC 27701; Employer Identification #44-4444444). Assume that all necessary deposits were...
-
A particle of mass 'm' is placed on the top of a smooth sphere of radius R. Particle is slightly displaced due to which it slides on the sphere before leaving contact with the sphere. Kinetic energy...
-
Called the "Ban the Box" movement, Koch Industries is the latest large U.S. corporation (employing more than 60,000 people in the United States alone) to drop its application question about prior...
-
The policy defined women capable of bearing children as "all women except those whose inability to bear children is medically documented." The policy defined unacceptable lead exposure as the OSHA...
-
Kimberly Cloutier was a member of the Church of Body Modification. In 1997, during her job interview for a position at Costco, Ms. Cloutier sported four tattoos and multiple earrings, but she had no...
-
T-Mobile's CEO, John Legere, has made T-Mobile the "best wireless carrier," according to consumer reports. At the time of that glowing report, T-Mobile had passed by Sprint to become the third...
-
On January 11, 1993, young Michael Nole and his family ate dinner at a Jack-in-the-Box restaurant in Tacoma, Washington, where Michael enjoyed his \(\$ 2.69\) "Kid's Meal." The next day, Michael was...
-
What is the frequency of light that has a wavelength of 1 8 5 nm ? (c= 3 . 0 0 1 0 8 m/s)
-
Compare and contrast licensing and subcontracting.
-
Two stepping motors are used in an open loop system to drive the lead screws for xy positioning. The range of each axis is 250 mm. The shafts of the motors are connected directly to the lead screws....
-
In the transfer line of Problems 16.20 and 16.22, suppose it is more technically feasible to locate the storage buffer between stations 11 and 12, rather than between stations 15 and 16. Determine...
-
A rotary worktable is driven by a Geneva mechanism with five slots. The driver rotates at 48 rev/min. Determine (a) The cycle time, (b) Available process time, and (c) Indexing time each cycle.
-
Describe the principle parts of a lathe with a neat sketch.
-
How a lathe is specified? Explain with a neat diagram.
-
How do you classify a lathe? Explain briefly.
Study smarter with the SolutionInn App