ARENA

. The project is an Electronic Assembly and Test System that represents the final operations of the production of two different sealed electronic units (see the process map shown below) Parep Para DO See - Soraped Salvaged and Sood Pune TRA Part ch Electronie Assembly and fear System System Description: Part A arrives to the model with inter arrival times being exponentially distributed with a mean of five minutes (all times are in minutes) Port Ais then instantly transferred to part A Preparation Area, where the nating faces of the cases are machined to ensure a good seal. The part is then deburred and cleaned the process time for the combined operation follows a triangular distribution TRIA(1,4,8). The part is then transferred instantly 10 the teler Part B is held until a batch of four units is available: the time between arrivals of successive batches is exponential with a mean of thirty minutes. Upon arrival of the Part preparation area, the batch is separated into four Individual units. These individual units proceed instantly to part B preparation area Similarly, each is going to be machined deburred and cleaned in the Prep process area. The process time for the combined operations follows TRIA (3.5.10) distribution . At the sealer the electronic components are inserted, the case is assembled and sealed, and the sealed unit is tested. The total process time for these operations depends on the part type: TRIA (134) for part A and WEIB(2553) for Port Ninety-one percent of the parts pass the inspection and are transferred instantly to the shipping department. The remaining parts processed of the rework area where they are disassembled, repaired, cleaned, assembled and retested Eighty percent of these parts are salvaged and transferred to the shipping department and the rest are transferred to the scrap area. The time to rework a port follows an exponential distribution with the mean of forty five minutes One you understood the process flow, you need to develop a conceptual Simulation model and decide on what data to collect from the model and what ARENA entities are needed for the model . You also need to verify the model before analyzing its results. Final Model / Output Analyst: When ready to run the model, but please consider several things: Enter the Project title (WITH YOUR TEAM IDENTITY) and analyst name (Team leader) so they will appear on the output reports. Ft Anem - Clear the Entities selection so we won't get statistics on time in system stored out by entity type. - You may then experiment the difference in the resulting reports if you keep the Entity statistics option checked then rerun your model. - We have to tell the arena simulation software when to stop. Otherwise it will run forever - So set the replication length to 80 hours, the base time units to minutes and default the remaining fields. (if number of entities in the model exceeded allowable limit use, use a run time of 8 hours with 10 replications). - Now since we have two different entities, it might be nice if we could distinguish between them by changing the Initial Picture of each entity from the Data Entity Module found in the basic process panel w Entty This model requires: Entities are the individual parts two types, A and B Create modules for two part types Process modules for each Prep area Process modules for Sealer and Rework, each followed by a Decide module (2-way choice that provides a Pass or Fail that meets the conditions) Depart modules for Shipping, Salvage/Shipped, Scrap Attribute Sealer Time assigned after Creates in Assign modules (parts have different times at the Sealer) Record modules just before Departs for time in system Building the Model with ARENA: To build the model, you need to open a new model window and place the required modules on the screen (the following is an example of a complete model but you can develop your own with different names of modules) PartArt Asin PIA and for Time Yep Apocs Sealer Process Part Arrive Assign Part Senter and Hep B Process! led Sealer inspecte fework Proces Failed Rework Inspection Record Scrap Parts Scrapped Record Savage Parte Salvaged 100 Record Shipped Part . The project is an Electronic Assembly and Test System that represents the final operations of the production of two different sealed electronic units (see the process map shown below) Parep Para DO See - Soraped Salvaged and Sood Pune TRA Part ch Electronie Assembly and fear System System Description: Part A arrives to the model with inter arrival times being exponentially distributed with a mean of five minutes (all times are in minutes) Port Ais then instantly transferred to part A Preparation Area, where the nating faces of the cases are machined to ensure a good seal. The part is then deburred and cleaned the process time for the combined operation follows a triangular distribution TRIA(1,4,8). The part is then transferred instantly 10 the teler Part B is held until a batch of four units is available: the time between arrivals of successive batches is exponential with a mean of thirty minutes. Upon arrival of the Part preparation area, the batch is separated into four Individual units. These individual units proceed instantly to part B preparation area Similarly, each is going to be machined deburred and cleaned in the Prep process area. The process time for the combined operations follows TRIA (3.5.10) distribution . At the sealer the electronic components are inserted, the case is assembled and sealed, and the sealed unit is tested. The total process time for these operations depends on the part type: TRIA (134) for part A and WEIB(2553) for Port Ninety-one percent of the parts pass the inspection and are transferred instantly to the shipping department. The remaining parts processed of the rework area where they are disassembled, repaired, cleaned, assembled and retested Eighty percent of these parts are salvaged and transferred to the shipping department and the rest are transferred to the scrap area. The time to rework a port follows an exponential distribution with the mean of forty five minutes One you understood the process flow, you need to develop a conceptual Simulation model and decide on what data to collect from the model and what ARENA entities are needed for the model . You also need to verify the model before analyzing its results. Final Model / Output Analyst: When ready to run the model, but please consider several things: Enter the Project title (WITH YOUR TEAM IDENTITY) and analyst name (Team leader) so they will appear on the output reports. Ft Anem - Clear the Entities selection so we won't get statistics on time in system stored out by entity type. - You may then experiment the difference in the resulting reports if you keep the Entity statistics option checked then rerun your model. - We have to tell the arena simulation software when to stop. Otherwise it will run forever - So set the replication length to 80 hours, the base time units to minutes and default the remaining fields. (if number of entities in the model exceeded allowable limit use, use a run time of 8 hours with 10 replications). - Now since we have two different entities, it might be nice if we could distinguish between them by changing the Initial Picture of each entity from the Data Entity Module found in the basic process panel w Entty This model requires: Entities are the individual parts two types, A and B Create modules for two part types Process modules for each Prep area Process modules for Sealer and Rework, each followed by a Decide module (2-way choice that provides a Pass or Fail that meets the conditions) Depart modules for Shipping, Salvage/Shipped, Scrap Attribute Sealer Time assigned after Creates in Assign modules (parts have different times at the Sealer) Record modules just before Departs for time in system Building the Model with ARENA: To build the model, you need to open a new model window and place the required modules on the screen (the following is an example of a complete model but you can develop your own with different names of modules) PartArt Asin PIA and for Time Yep Apocs Sealer Process Part Arrive Assign Part Senter and Hep B Process! led Sealer inspecte fework Proces Failed Rework Inspection Record Scrap Parts Scrapped Record Savage Parte Salvaged 100 Record Shipped Part