Question: Calculate : 2. Calculate the allowable load Pall for the bolted connection shown in Figure Q2. Given: the strength in tension and bearing is 210

Calculate :

2. Calculate the allowable load Pall for the bolted connection shown in Figure Q2. Given: the strength in tension and bearing is 210 MPa and the shear strength of the bolt at C is 140 MPa. Further, w = 50 mm, t = 6 mm, d = 12 mm and a Factor of Safety of 1.6 is used. Bar Figure Q2 B A 2.5 kN 7.5 kN D 25.1 kN E 9.45 kN 15.3 KN

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

I need help to solve my 3-month project for payroll accounting (Three-Month Project) Ampersand, Inc. Ampersand, Inc., is a small business that operates in Somerset, VT. The company is located at 732...

Calculate the allowable load Pall for the bolted connection shown in Figure Q 2 . Given: the strength in tension and bearing is 2 1 0 MPa and the shear strength of the bolt at C is 1 4 0 MPa....

Design of a Strip Footing Design ( 2 5 Marks ) Design of a Strip Footing Design ( 2 5 Marks ) Figure 2 shows a 2 - Storey Reinforced Concrete Structure. All External and Internal wall consists of a...

SITUATION: The diagonal at the left to the connection shown in figure, is a double angle 9 0 m m 9 0 m m 8 m m , with area of 2 7 0 0 m m 2 , bolted to the 8 - mm thick gusset plate. Bolt diameter, d...

Drawing A in Figure 1 shows a secondary shaft with a helical gear ( B ) , a bevel gear ( D ) , and two support bearings ( A and C ) . The loads acting on the bevel gear are shown. The forces on the...

Note: G40.21M-350W (Fy =350 MPa, Fu = 450 MPa) steel is to be used, unless otherwise specified. None of the beams in this assignment are cambered. It is not permitted to use M, values obtained from...

Problem 1 . Bolted Connection Evaluation A rolled 1 5 0 x 1 0 0 x 1 0 UA made of Grade 3 5 0 steel is connected by two rows of Grade 8 . 8 M 2 4 X ( refer to page 1 5 4 for definition of X ) bolts in...

Q 2 : Design of Bolted Connection for Steel Structure A team of structural engineers is designing a bolted connection for a steel structure. The connection must transfer significant loads while...

2 . ) A steel bar is attached to a wood support beam with four 2 2 mm diameter lag screws, as shown in the figure. The steel bar is 6 8 - mm - wide by 5 - mm - thick. For the steel bar, the yield...

A tension member made of 2 UPE 2 7 0 section is connected to a gusset plate t p = 2 5 m m with M 2 0 - 1 0 . 9 bearing type bolts. The tension member is subjected to axial tensile force of P G = 2 5...

Problem 1 (2+8 marko Why is preloading important for a bolted connection? How should one control the applied presad? 11. A hydro-cylinder with an inner diameter of D-160 mm is shown in Figure 1. Oil...

A group of people are asked to target weighing out 75 lbs for each sample. There were 78 people who participated in this study. The next page shows a control chart of their measurements. The average...

Which of the followings aspects of international law weuld enable a cyber - criminal operating across boriders to ivade prosecution? a . Lack of sechnolegy to identify the origin of a security amack...

Calculate the mean free path of air molecules at a pressure of 3.50 X 10-13 atm and a temperature of 300 K. (This pressure is readily attainable in the laboratory; see Exercise 18.24.) As in Example...

Consider 5.00 mol of liquid water. (a) What volume is occupied by this amount of water? The molar mass of water is 18.0 g/mol (b) Imagine the molecules to be, on average, uniformly spaced, with each...

What is the magnitude of the magnetic dipole moment of the solenoid?

A bar magnet is spun at constant angular speed w around an axis as shown in Figure P31.38. A stationary flat rectangular conducting loop surrounds the magnet, and at t = 0, the magnet is oriented as...

Reaction of 2-butanone with HCN yields a chiral product. What stereochemistry does the product have? Is it optically active?

Question 1 3 Which of the following modes of transportation is said to be slowest? road Maritime Railroad The speed of transportation is not dependent on the mode of transportation

Describe what a one-minute self-sell is and what it contains.

Define the following 14 key terms throughout the chapter identified in bold with their definition in italic font. They are listed at the end of the chapter.

List and explain the steps in the negotiating process.