Question: Consider a double-issue processor (issue any. 16 two instructions) assuming that the processor consists of four stages (IS, EX, M and WR on CDB). Also,

Consider a double-issue processor (issue any. 16 two instructions) assuming that the processor consists of four stages (IS, EX, M and WR on CDB). Also, if two instructions contend for the CDB in the same cycle (completed), the oldest instruction is awarded the CDB The following table gives the EX latencies Operation type Time in EX Any integer operation FP adder FP multiplier 2 5 10 In the following table fill out the blank entries with the cycle number(s) of each event Instruction IS EX WR LD.D FO, 0(x1) 1 2-3 4 5 ADD.D F1, FO, FO SD.D 4(x1), F1 (LD.D F2, 4(x1 MUL.D F3, F2, F1 MUL.D F4, F1, F1 ADD.D F5, F4, F3 MUL.D F6. F1. FO Any integer operation FP adder FP multiplier 10 In the following table fill out the blank entries with .the cycle number(s) of each event Instruction IS EX WR LD.D FO, 0(x1) 1 2-3 4 5 ADD.D F1, FO, FO SD.D 4(x1), F1 (LD.D F2, 4(x1 MUL.D F3, F2, F1 MUL.D F4, F1, F1 ADD.D F5, F4, F3 MUL.D F6, F1, FO ADD.D F7, F4, FO (LD.D F8, 8(F7 ADD.D F10, F1, F1 MUL.D F9, F1, FO Use extra paper to solve the question and upload .your solution !Show your solution in details ( (6 ) Consider a double-issue processor (issue any. 16 two instructions) assuming that the processor consists of four stages (IS, EX, M and WR on CDB). Also, if two instructions contend for the CDB in the same cycle (completed), the oldest instruction is awarded the CDB The following table gives the EX latencies Operation type Time in EX Any integer operation FP adder FP multiplier 2 5 10 In the following table fill out the blank entries with the cycle number(s) of each event Instruction IS EX WR LD.D FO, 0(x1) 1 2-3 4 5 ADD.D F1, FO, FO SD.D 4(x1), F1 (LD.D F2, 4(x1 MUL.D F3, F2, F1 MUL.D F4, F1, F1 ADD.D F5, F4, F3 MUL.D F6. F1. FO Any integer operation FP adder FP multiplier 10 In the following table fill out the blank entries with .the cycle number(s) of each event Instruction IS EX WR LD.D FO, 0(x1) 1 2-3 4 5 ADD.D F1, FO, FO SD.D 4(x1), F1 (LD.D F2, 4(x1 MUL.D F3, F2, F1 MUL.D F4, F1, F1 ADD.D F5, F4, F3 MUL.D F6, F1, FO ADD.D F7, F4, FO (LD.D F8, 8(F7 ADD.D F10, F1, F1 MUL.D F9, F1, FO Use extra paper to solve the question and upload .your solution !Show your solution in details ( (6 )

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Provide a summary technical report with your own words about Pipelined Execution which is also named as Instruction Level Parallelism, addressing mainly the following areas: 1. What is Pipelined...

ADVANCED COMPUTER ARCHITECTURE CPCS504 Assignment1 Spring 2021 /1442 Due Date 1st March 2021 Chapter1: 1. In Example 1 of Section 1.2.1, we assumed that the cache miss penalty was 20 cycles. With...

Computer Organization and Networks Practicals 2021/22 October 9, 2021 Computer Organization and Networks Practicals 2021/22 b68495714b Contents Contents 0 Introduction 3 0.1 Registration . . . . . ....

f a processor exhibited one branch delay slot how would you reorder (and possibly modify) the instructions in the following loop to gain a performance advantage? loop ldr r2,r3,#4 % r2=load(r3),...

Q 1 Consider the 8 - stage pipelined processor with two execution units and pipelined caches, as shown below. Instruction fetch is a two - stage process followed by decode where registers are also...

Consider the following sequence of instructions, where the syntax consists of an opcode followed by the destination register followed by one or two source registers: 0 ADD R3, R1, R2 1 LOAD R6, [R3]...

Consider the following sequence of instructions, where the syntax consists of an opcode followed by the destination register followed by one or two source registers: R3, R1, R2 ADD LOADR6, [R3] AND...

18.2 Consider the following sequence of instructions, where the syntax consists of an opcode followed by the destination register followed by one or two source registers: 0 ADD R3, R1, R2 1 LOAD R6,...

Consider the following sequence of instructions, where the syntax consists of an opcode followed by the destination register followed by one or two source registers: Assume the use of a four-stage...

(a) In SystemVerilog, what is the difference between: (i) The ternary operator ? and if...then...else statements? [2 marks] (ii) always_ff and always_comb? [2 marks] (iii) Blocking, non-blocking and...

In a simple linear regression based on 25 observations, the following intermediate data are given: (yi - )2 = 1250 and (yi - )2 = 1500. a. Calculate se2 and se. b. Calculate R2.

The handcart has wheels with a diameter D. If a crate having a weight W is placed on the cart, determine the force P that must be applied to the handle to overcome the rolling resistance. The...

4. Identify the goods and services that you purchase that are imported. How would your lifestyle change if these imports were unavailable?

1. Consider each of the following processes: (i) (1 0.6B)Y = (1 -0.9B)et, (ii) (1 - 1.4B +0.6B2)Y; = (1 - 0.8B)et (a) Find the acf pk (b) Find the pacf Okk for k=1, 2. (c) Simulate a series of 100...

What are the Variable columns settings available in the Mining Models Tab?

What does the Mining Content Viewer in Visual Studio show in terms of Probabilities?

How are continuous variables normally handled in Decision Tree Algorithms?