Question: Determine the cutting force component Ft , parallel to the cutting velocity in turning of a steel shaft with carbide tool with following cutting conditions,

Determine the cutting force component Ft , parallel to the cutting velocity in turning of a steel shaft with carbide tool with following cutting conditions, depth of cut is 4 mm , feed ?rev is 0.5 mm cutting speed 120mmin, specific cutting resistance is 1380Nmm2
Determine the cutting force component Ft ,

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

2 0 . 5 ( A ) ( USCS units ) A turning operation is performed using a rake angle of 1 5 . Cutting speed = 2 0 0 f t m i n , feed = 0 . 0 1 2 i n r e v , and depth of cut = 0 . 1 0 0 i n . The chip...

Q:

The outside diameter of a roll for a steel (AISI 1015) rolling mill is to be turned. In the final pass, the starting diameter = 26.25 in. and the length 48.0 in. The cutting conditions will be feed =...

Q:

Two Discussion Questions. A minimum of 200 words per question. Both questions are attached to the word document and each chapter to both questions are attached to the PDF. Any references/citations...

Q:

A carbon steel bar with 2 0 0 mm diameter has a tensile strength of 4 3 0 MPa and a shear strength of 3 6 0 MPa . The diameter is reduced using a turning operation at a cutting speed of 1 2 0 m m i n...

Q:

Consider a lathe machine with a motor rated at 1 horsepower ( hp ) . Efficiency of this machine was found to be about 7 5 % . ( 1 0 pts each, 3 0 pts in total ) ( a ) Determine what is the maximum...

Q:

Consider the straight turning operation of a AISI 1 0 1 0 steel bar with a tool with a rake angle of 5 and a clearance angle of 3 , using the following operating parameters: cutting speed is 3 1 5 m...

Q:

The following machining conditions for a turning operation are given. Cutting speed: V = 6 5 m / min , feed rate: f = 0 . 1 5 mm / rev , and depth of cut w = 1 mm . The external workpiece diameter is...

Q:

Consider the selection of two cutting conditions for turning - the cutting speed, v, and the feed, f - based upon the minimum production time criterion and the surface nish. The cutting tool is a new...

Q:

In an orthogonal cutting operation the following data is obtained: Rake angle a = 2 0 \ deg Ch p thickness ratio = 0 . 4 Cutting force component parallel to cutting velocity = 1 6 0 0 N Cutting force...

Q:

Q1) Determine the cutting force and feed (thrust) force for a turning operation using the following parameters: Material tensile strength 250MPa, Shear strength 120 MPa, chip thickness ratio r =...

Q:

The book value of an asset that was DDB depreciated over a 10-year period was $5832 at the end of year 4. If the first cost of the asset was $80,000, the salvage value that was used in the...

Q:

If a project generates cash flow, which can be positive or negative, as shown in the table below (RMB Yuan), is the project financially feasible if the market interest rate is 8%? For example, you...

Q:

Robert and John are married and have 5 dependent children and earn a gross biweekly salary of \ ( \ $ 5 , 5 2 3 \ ) . They will also make the following taxdeductible purchases: - Medical expenses: \...

Q:

Suppose you build a new park in town. You are able to identifyevery persons individual WTP to enter the park. You charge avariable ticket fee, based on each persons WTP. Consumer surplusin this...