Question: For a particular item, the average demand is 1 0 0 units a week and the lead time is four weeks. If an order is

For a particular item, the average demand is 100units a week and the lead time is four weeks. If an order is placed when there are ____ units on hand, on average, there will be enough stock on hand to last until the new stock arrives.
Question 19 options:
A.100
B.400
C.300
D.1200

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Q:

Table 1 Inventory records show the following: Item Category # unique variations Average Cost Avg Monthly Vol Frames (C) 3 $ 45.00 100 Derialer 5 $ 20.00 1000 Spokes 3 $ 0.14 22000 Tire Tubes 3 $ 2.00...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost /high volume assemblies, the X0-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost / high volume assemblies, the XO-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

Answers only QUESTION 13 Constraints at any step causes imbalance in the capacity of a process. As a result, the overall performance of a system is affected which in turn leads to low customer...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost /high volume assemblies, the XO-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost /high volume assemblies, the XO-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost / high volume assemblies, the XO-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

The Talbot Company uses electrical assemblies to produce an array of small appliances. One of its high cost / high volume assemblies, the XO-01, has an estimated annual demand of 8,000 units. Talbot...

Q:

Use Table 1 to identify the best statement after determining the ABC categorization. Items Reflectors and Pumps fall in the same category of an ABC analysis. Items Frames (C) and Derialer fall in the...

Q:

each question matches to one of the multiple choice answers. Inventory records show the following: \begin{tabular}{|c|c|c|c|c|} \hline \begin{tabular}{l} Item \\ Category \end{tabular} &...

Q:

A barbershop has been using a level workforce of barbers five days per week, Tuesday through Saturday. The barbers have considerable idle time on Tuesday through Friday, with certain peak periods...

Q:

An aluminum fin is used for cooling of the high capacity of chip. Dimensions of the fin can be seen in figure below. Surface temperature of the chip is 88C. The chip is cooled by air flow. (Note:...

Q:

Which of these is most apt to decrease the cash cycle? 1 9 Multiple ChoiceDecreasing the inventory turnover rateIncreasing the receivables periodDecreasing the accounts receivable turnover...

Q:

Make a statement of cashflows in good form. X X M Inbox 2,50 x M Logistics : * Course: ST: X|MyDrive- x B Group 2 Pex Course ID: Cth Moodle X C Get HomeX C Photos Screx Interview X + ....