Question: For the following system: a ) Determine the offset for a unit step change in the set point. 6 points b ) Determine the offset

For the following system:
a) Determine the offset for a unit step change in the set point. 6 points
b) Determine the offset for a step change in the disturbance of magnitude 2
For the following system: a) Determine the offset for a unit

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

Q 3 . The liquid level in the second tank for a noninteracting tank system is controlled by manipulating the inlet flow rate of the first tank. All of the resistances are linear and R 1 = 0 . 0 5 , R...

Q:

Question 4 Consider the closed-loop systems shown in Figure 1, where the transfer function of the process is that of a second-order system as shown: Gp(s)=p2s2+2s+1kpWhere(kp=1,=0.5,=0.5,kc=5) Figure...

Q:

Question 1 In a cascade control of a furnace, the exit temperature, T is controlled by manipulating the flow rate of fuel F; fed to a furnace. Both the outer and inner loops are proportional-only...

Q:

Question 1 In a cascade control of a furnace, the exit temperature, T is controlled by manipulating the flow rate of fuel Ffed to a furnace. Both the outer and inner loops are proportional-only...

Q:

it's a process control an Instrumentation based problem please solve it 5. Construct the block diagram of a feed back control system comprising an integrating level process, a P controller with gain...

Q:

7. For a general closed loop system with Gp(S)=1/[(s+1)(2s+1)],Gm=1.6,Gc=Gf1, an unit step change to set point is given. Determine (a) the maximum value of output and the time at which it occurs, (b)...

Q:

Consider the closed-loop system shown in Figure P11.6, where the transfer function of the process is that of a second-order system, i.e. k Ts +25TS +1 G,(s)= Y sp(s) E(s) U(s) Y(s) Ge(s) Gp(s) Figure...

Q:

A conventional feedback control system depicted in Fig. 1 is considered. The curves (A, B, C) shown in Fig. 2a illustrate the closed-loop responses of the process under P, PI, and PID control after a...

Q:

A process with two major time constants of 2 and 5 mins and process gains of 1 and 2 is controlled by a proportional controller. Determine the controller gain to produce a damping ratio of 0.7....

Q:

Consider the transfer function model of Exercise 20.1. For each of the four sets of design parameters shown below, design a model predictive controller. Then do the following: (a) Compare the...

Q:

What portfolio would you recommend to a 28yearold who has just been promoted to a management position and what portfolio would you recommend to a 60yearold who has just retired

Q:

What is a journal voucher? Describe how computer batch processing of journal vouchers may be used to update the general ledger.

Q:

A / an q , is a type of investor who uses his or her own money to provide funds to young startup private businesses run by entrepreneurs who are neither friends nor family. Time Elaps Aemempt due: 5...

Q:

Please answer for all parts last time the expert does not give the properly answer Exercise 4 (20 points) Consider the recurrence equation Solve this recurrence equation: a) With the recursive tree...

Q:

If you exclude the city from the previous question from analysis, what sales rank does Arkansas fall to?

Q:

Which three states had the lowest sales volume for the two weeks of analysis?

Q:

Compare and contrast the stacked bar chart produced by Tableau Desktop with the one produced by Power BI Desktop. Which one is easier to interact with?