Question: For the given wooden beam and cross section, a) Determine the maximum magnitude of P ( P>0) by considering the following properties for wood

For the given wooden beam and cross section, a) Determine the maximum

magnitude of P ( P>0) by considering the following properties for wood

For the given wooden beam and cross section, a) Determine the maximum magnitude of P ( P>0) by considering the following properties for wood and glue: [20] The allowable shear stress of wood: 30 MPa The allowable shear stress of glue: 40 MPa b) Determine the maximum spacing of nails if the maximum allowable shear force for each nail is 100KN and P is 20 kN. [10] |P kN 10 kN/m K2m 2 m timt 100mm- 5 mm' 5 mm. Glue 5 mm 5 mm Cross Section 80 mm

Step by Step Solution

★★★★★

3.35 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a Nomenclate the beam as follows Taking moments about B we get V A 5 1022P1 5V ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Black Oil Company is trying to decide whether to lease or buy a new computer-assisted drilling system for its extraction business. Management has already determined that acquisition of the system has...

Determine the maximum magnitude of the bending moment M so that the bending stress in the member does not exceed 15 ksi. 4 in. 4 in. 6 in. ID -6 in.-

A steel beam of rectangular cross section is 40 mm wide and 80 mm high (see figure). The yield stress of the steel is 210 MPa. (a) What percent of the cross-sectional area is occupied by the elastic...

The wood beam has an allowable shear stress of Ï allow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section. 50 mm 50 mm +100 mm- 50 mm 200 mm 50 mm

Data, Inc., purchased and placed in service $5,000 of office furniture on August 24, year 3- This is the only asset purchase during the year. Section 179 expensing was not elected. Using the excerpt...

A vapor flows through a pipe with a mass flow rate (m) of 30 kg/min. The following properties are given at a particular cross section, Area: 10 cm2, Velocity: 60 m/s, Specific flow energy (j): 281.89...

In LIGO and other GW interferometers, one potential source of noise is scattered light. When the Gaussian beam in one of LIGOs cavities reflects off a mirror, a small portion of the light gets...

1-Draw Plan and Cross section of a Tee beam concrete deck bridge. The deck is required for the crossing of a national highway. The available data is given as below: Effective span = 20 m, Clear...

For the angle cross section indicated, determine the orientation of the principal axes at the origin and the corresponding values of the moments of inertia. The L76 Ã 51 Ã 6.4-mm angle...

For the angle cross section indicated, determine the orientation of the principal axes at the origin and the corresponding values of the moments of inertia. The L5 Ã 3 Ã 1/2-in.angle...

Because of the large number of devices in today's PC chips, finned heat sinks are often used to maintain the chip at an acceptable operating temperature. Two fin designs are to be evaluated, both of...

Show how a production possibility curve would shift if a society became more productive in its output of widgets but less productive in its output of wadgets.

For a fully continuous 15-year term life insurance of 1000 on (60) : (i) = 0.04 (ii) = 0.02 (iii) Annual net premium = 40. Calculate the probability that the future loss is greater than 10.

Evaluate the following limit . lim h 0 4 3 h - 4 3 h Rewrite the given limit in a way that can be evaluated by direct substitution.

Find the force in each of the five wires that make up this system. The mass m is 200. All wires are tied to the E 45 rings. 60

Four charges of equal magnitude 7.65 C are arranged at the corners of a square of side 9.12 cm as shown in the Figure. Notice that some charges have "-" sign. Find the magnitude and direction of the...

A thin rod extends along the z -axis from z = -d to z = d. The rod carries a positive charge Quniformly distributed along its length 2d with charge density 51.86 C/m. If the electron started out at...

A thin rod extends along the z -axis from z = -d to z = d. The rod carries a positive charge Quniformly distributed along its length 2d with charge density 13.1 C/m. What is the change in potential...

Suppose the electric potential due to a certain charge distribution can be written in Cartesian Coordinates as V(xyz)=2 x*y. What is the magnitude of the electric field at the point (1,1,1)? Your...

Which of the following is based on the assumption that the future will be an extrapolation of the past? Question 77Answer a. The Delphi method b. Statistical forecasting c. The Cooke method d....

Sample Output : For Beam #1: The length of the beam is d = 8 feet which is equal to 96 inches The length of the base is b = 2 inches The height of the beam is h = 4 inches The stress on the fixed end...

3. The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2, can be calculated as the following L = $x1 dxc L is the maximum weight...

Provide a java program for the following problem: The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2, can be calculated as the...

The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2, can be calculated as the following: L is the maximum weight in lbs of the...

2. (Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given...

Need help ASAP!!!! please follow the instructions for programming this problem. I'm using C++ visual studios Question 3 The maximum load that can be placed at the end of a symmetrical wooden beam,...