Question: A steel beam of rectangular cross section is 40 mm wide and 80 mm high (see figure). The yield stress of the steel is 210

A steel beam of rectangular cross section is 40 mm wide and 80 mm high (see figure). The yield stress of the steel is 210 MPa.
(a) What percent of the cross-sectional area is occupied by the elastic core if the beam is subjected to a bending moment of 12.0 kNm acting about the z axis?
(b) What is the magnitude of the bending moment that will cause 50% of the cross section to yield?

80 mm 40 mm

Step by Step Solution

★★★★★

3.40 Rating (156 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

y 210 MPa b 40 mm h 80 mm a ELASTIC ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (614).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

A cantilever beam of rectangular cross section is subjected to a concentrated load P = 17 k acting at the free end (see figure). The beam has width b = 3 in. and height h = 12 in. Point A is located...

A simply supported wood beam of rectangular cross section and span length 1.2m carries a concentrated load P at mid span in addition to its own weight (see figure). The cross section has width 140mm...

A beam of rectangular cross section supports an inclined load P having its line of action along a diagonal of the cross section (see figure). Show that the neutral axis lies along the other diagonal....

A pretensioned concrete beam of rectangular cross section, 1 5 0 mm wide and 3 0 0 mm deep, is prestressed by eight high tensile wires of 7 mm diameter located at 1 0 0 mm from the soffit of the...

An overhanging beam ABC with a guided support at A is of rectangular cross section and supports concentrated loads P both at A and at the free end C (see figure). The span length from A to B is L,...

A timber column 3m high has a rectangular cross section, 100mm x 200mm, and is reinforced over its entire length by two steel plates each 200 mm wide by 10 mm thick attached to the 20mm faces. The...

COMPACTNESS and EFFECTIVE SECTION MODULUS Question: Verify the compactness and Z ex and Z ey values of section 500 WC 228 Grade 400 (Note: 7 th Edition Hot Rolled Structural Steel Products) Notes...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Each arm comprises a horizontal beam made from an AISI651 stainless steel tube (see Table 1 for the material properties) of length L = 35 mm, inner diameter d = 375 m and outer diameter do = 575 m,...

What is the economic justification for the sticky inflation assumption? What role does this assumption play in the short-run model?

A parallel-plate capacitor has the volume between its plates filled with plastic with dielectric constant K. The magnitude of the charge on each plate is Q. Each plate has area a. and the distance...

The approach to identify company profit centers may vary-by contract type, by market, by type of work-but what characteristic should be common to all?

100. On the Coast is a very popular restaurant located along the coast of Lake Erie. It serves a variety of steak and seafood dinners. During the summer beach season, it does not take reservations or...

The piece of rubber is originally rectangular and subjected to the deformation shown by the dashed lines. Determine the average normal strain along the diagonal DB and side AD. 3 mm- D 400 mm -x A...

The piece of rubber is originally rectangular. Determine the average shear strain xy at A if the corners B and D are subjected to the displacements that cause the rubber to distort as shown by the...

The rigid beam is supported by a pin at B and wires AD and CE. If the load P on the beam causes the end A to be displaced 6 mm downward, determine the normal strain developed in wires CE and AD. The...

Pertormed counseling services tor $ 3 0 , 0 0 0 cash. On February 1 , Year 1 , paid $ 2 1 , 0 0 0 cash to rent office space for the coming year. Adjusted the accounts to reflect the amount of rent...

Tom is considering purchasing a $ 20 000 car. After five years, he will be able to sell the vehicle for $ 10 000. Petrol costs will be $ 2 000 per year, insurance $600 per year, and parking S 600 per...

You are analyzing the purchase of new equipment. Since you are not an expert on this type of equipment, you hire a consulting firm to make recommendations. The consultant charged you $1,500 and...