Question: For the uniform beam below, A , C and D are roller supported and F is fix connected to the wall. The beam is subjected

For the uniform beam below, A, C and D are roller supported and F is fix
connected to the wall. The beam is subjected to concentrated loads of 40 kN at point B,60kN at point E, and a clockwise concentrated moment of 60 kNm at point A. Please use the force method to solve the reaction forces at A, C, D and F,and the moment diagram.
For the uniform beam below, A , C and D are

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Segments AB and BCD of beam ABCD are pin connected at x =10 ft. The beam is supported by pin support at A and roller supports at C and D; the roller at D is rotated by 308 from the x axis (see...

Q:

9. The uniform beam of mass m = 11.0 kg shown is supported at its left end by a hinge attached to a wall and on its right end by a scale sitting on the floor. A weight W is suspended half way between...

Q:

Problem 3 : Problem 3 : A beam ABCD consists of two segments A B and B C D that are pin connected at x = 4 m . The beam is supported by a slider support at A and roller supports at C and D as shown...

Q:

Part B - Maximum shear at C Determine the maximum positive shear that can be developed at point C . Express your answer in kN to three significant figures. View Available Hint ( s ) ( V C ) m a x = X...

Q:

Learning Goal: To find the maximum reaction, shear, and moment at specified points in a beam that is subjected to moving loads. This tutorial will use influence lines to find these maximum values....

Q:

HW 6 Problem 1 : Determine whether a W 1 4 9 0 is compact, noncompact, or slender for F y = 6 0 ksi.Determine whether a W 6 1 5 is compact, noncompact, or slender for F y = 6 0 ksi. Problem 2 The...

Q:

SECTION A Read the entire exercise (all questions) before beginning. More compensation information is available than ever before. Go to www.salary.com (Links to an external site.) or any other...

Q:

Learning Goal: Influence lines are constructed using a dimensionless unit load Therefore, the value of the function for any concentrated force F can be found by multiplying the ordinate of the...

Q:

A = 2 B = 2 C = 5 D = 1 Problem #4 A concentrated live of 25 kips and distributed live load of 3 kips/ft can be placed anywhere on the beam, determine the maximum positive shear force at C and...

Q:

Problem 3 : A beam ABCD consists of two segments A B and B C D that are pin connected at x = 4 m . The beam is supported by a slider support at A and roller supports at C and D as shown in figure...

Q:

A smooth uniform rod AB of mass M and length l rotates freely with an angular velocity o in a horizontal plane about a stationary vertical axis passing through its end A. A small sleeve of mass m...

Q:

The following is the balance sheet of Korver Supply Company at December 31, 2015 The note payable is dated June 30, 2015 and is due on June 30, 2017. Interest at 10% is payable annually on June 30....

Q:

The production cost is 5 0 % of the monthly sales, which it will be produced a month before the sales, comprises of: Labor: 3 0 % , and to be paid a month after the production month Production cost:...

Q:

You have the following employee sales data: Q1 Q2 Q3 Sales $600 $650 $401.20 You also know the following assumptions: COGS % of Sales is: 70%, 65%, and 68% (respectively for Q1 - Q3) Operating...