human res

amplele in one sitting. Do not leave the test before clicking Remaining Time: 56 minutes, 14 seconds. Question Completion Status: QUESTION 1 Rsum mining allows HR staff to use software to extract the most promising rsums from a large database. True False QUESTION 2 Recruiting is essentially an administrative function rather than a part of strategic HR planning, True False some of the possible explanations for not finding any causes? What should the manager do? 2. Many organizations use the same process capability standard for all their products or services (e.g.. 1.33), but some companies use multiple standards: different standards for different products or services (e.g., 1.00, 1.20, 1.33, and 1.40). What reasons might there be for using a single mea- sure, and what reasons might there be for using multiple standards? 3. Give two examples of unethical behavior for each of these areas: inspection, process control, pro- cess capability. For cach, name the relevant ethical principle (see Chapter 1). 4. In repetitive operations it is often possible to automatically check for quality and then reject parts that are unacceptable. In those situations, does that mean that control charts arent needed? Explain. Specifications for a part for a DVD player state that the part should weigh between 24 and 25 ounces. The process that produces the parts has a mean of 24.5 ounces and a standard deviation of .2 ounce. The distribution of output is normal. a. What percentage of parts will not meet the weight specs? b. Within what values will 95.44 percent of sample means of this process fall, if samples of n = 16 are taken and the process is in control (random)? 2. An automatic filling machine is used to fill 1-liter bottles of cola. The machine's output is approxi- mately normal with a mean of 1.0 liter and a standard deviation of .01 liter. Output is monitored using means of samples of 25 observations. a. Determine upper and lower control limits that will include roughly 97 percent of the sample means when the process is in control b. Given these sample means: 1.005, 1.001..998, 1.002..995, and .999, is the process in control? 3. The time to replace vehicle wiper blades at a service center was monitored using a mean and a range At Six samples of n = 20 observations were obtained and the sample means and ranges computed: * BINIMIIN command amplele in one sitting. Do not leave the test before clicking Remaining Time: 56 minutes, 14 seconds. Question Completion Status: QUESTION 1 Rsum mining allows HR staff to use software to extract the most promising rsums from a large database. True False QUESTION 2 Recruiting is essentially an administrative function rather than a part of strategic HR planning, True False some of the possible explanations for not finding any causes? What should the manager do? 2. Many organizations use the same process capability standard for all their products or services (e.g.. 1.33), but some companies use multiple standards: different standards for different products or services (e.g., 1.00, 1.20, 1.33, and 1.40). What reasons might there be for using a single mea- sure, and what reasons might there be for using multiple standards? 3. Give two examples of unethical behavior for each of these areas: inspection, process control, pro- cess capability. For cach, name the relevant ethical principle (see Chapter 1). 4. In repetitive operations it is often possible to automatically check for quality and then reject parts that are unacceptable. In those situations, does that mean that control charts arent needed? Explain. Specifications for a part for a DVD player state that the part should weigh between 24 and 25 ounces. The process that produces the parts has a mean of 24.5 ounces and a standard deviation of .2 ounce. The distribution of output is normal. a. What percentage of parts will not meet the weight specs? b. Within what values will 95.44 percent of sample means of this process fall, if samples of n = 16 are taken and the process is in control (random)? 2. An automatic filling machine is used to fill 1-liter bottles of cola. The machine's output is approxi- mately normal with a mean of 1.0 liter and a standard deviation of .01 liter. Output is monitored using means of samples of 25 observations. a. Determine upper and lower control limits that will include roughly 97 percent of the sample means when the process is in control b. Given these sample means: 1.005, 1.001..998, 1.002..995, and .999, is the process in control? 3. The time to replace vehicle wiper blades at a service center was monitored using a mean and a range At Six samples of n = 20 observations were obtained and the sample means and ranges computed: * BINIMIIN command