Question: If we have multiple loads on an axial bar as shown with the following parameters, what is the overall displacement in microns? k1=223 kN/mm

If we have multiple loads on an axial bar as shown with the following parameters, what is the overall displacement in microns? k1=223 kN/mm k2=162 kN/mm k3-113 kN/mm F1=1 kN F2=1.3 kN F3=3 KN kz K Fi F k3 F3

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

The partnership agreement of the G&P general partnership states that Gary will receive a guaranteed payment of $13,000, and that Gary and Prudence will share the remaining profits or losses in a...

California law limits the standard deduction of a person who isclaimed as a dependent. In 2022, the standard deduction fordependents in California is what amount 2 answers

Assume that the balance-of-payments accounts for a country are recorded correctly. Balance on the current account = BCA = $130 billion Balance on the capital/financial account = BKA = $86 billion...

On July 1, 2019, Brent purchases a new automobile for $35,500. He uses the car 84% for business and drives the car for business purposes as follows: 8,000 miles in 2019, 20,000 miles in 2020, 22,400...

An axial bar xed at both ends with no loads applied is subjected to an increase of temperature. The axial stress that will be induced in the bar will be: 0 Compressive 0 none of the choices 0 Tensile...

helpDesign of Column in Simple Construction Figure 1 ( a ) shows a floor layout at level 1 of an office building, built in simple conistruction. The loading's are given as follows: Loads from slab: (...

ASSIGNMENT 1 Design of Column in Simple Construction Figure 1 ( a ) shows a floor layout at level 1 of an office building, built in simple construction. The loadings are given as follows: Loads from...

Figure 1 ( a ) shows a floor layout at level 1 of an office building, built in simple conistruction. The loadings are given as follows Loads from slab: ( i ) . Unfactored dead load including the...

please see attachment: Question: Use a 0.010 significance level to test the claim that cans 0.0109 inches thick have a lower mean axial load than cans that are 0.0111 inches thick. Below are the...

For this computing project, first you need to derive the equations for the tension in cable AB, the tension in cable CD and the reaction at O in terms of x, which represents the placement of the...

Problem 3 : Two cantilever beams AB and CD are connected to an axial bar BD . A rigid block is located a small distance s above point B . Beam AB has flexural rigidity E I and length L . Beam CD has...

A and B are partners in a firm sharing profits and losses in the ratio of 3:1. On 31" December 2020 they admitted C as a partner for % share in the future profits. C was to bring RO 60000 as his...

what does the symbol @ mean in matlab. For example what does it mean in the following code: f= @(w)(vo/wn)*sin(wn*t) + (xo-(fo/(wn.^2- w.^2)))*cos(wn*t) + (fo/(wn.^2 - w.^2))*cos(w*t) -x; Assume that...

M10.C1: Group Final Paper : Purpose of Assignment: This paper gives you an opportunity to demonstrate your ability to plan a group, taking into account structural, organizational, and design factors....

11. Ashkenazim, French Canadians, and people who live in southwestern Louisiana have a higher incidence of Tay-Sachs disease than other populations. Each of these groups has a different mutation. How...

29. Refer to Exhibit 23-8. What is the total variable cost of firm A at the profit-maximizing (or loss- 29. Refer to Exhibit 23-8. What is the total variable cost of firm A at the profit-maximizing...

4. Describe a pair of allelic disorders.

a cyclic process consists of three steps at firt step heat is 150J and work is -70J in the second step heat is -160J and work is 110J and in third step heat is 90J then finds the work for third step...

Explain how to recognize the revenue if you have the information below.Use a boldface typefor importantaccounting terminologies or words in your report. The A company sells copy machine at a sales...

Determine if the overhead allocated to the product relates to a single plantwide overhead rate method, multiple production department factory overhead rate method, or activity-based costing...

4. TEAM EXERCISE Form small groups, and describe and evaluate your college or universitys website. A different member of the group might carry out each of the following tasks: In an email to the...

2. In a small group, discuss the following questions and rewrite the titles below. Appoint a spokesperson for your group to report back to the class. Questions: How clearly does the title indicate...

3. When the agent is less important than the action: The blueprints were hand-delivered this morning. It doesnt matter who the messenger was.