Question: If we use the PC - relative addressing mode, and want to jump to instructions 2 0 memory locations away, how many bits of a

If we use the PC-relative addressing mode, and want to jump to instructions 20 memory locations away, how many bits of a branch instruction are needed to specify the PC-relative offset? (Assume a 2s complement offset)

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

(12pt) The branch instructions, like bne and beq, use the PC relative addressing mode while the jump instructions use the pseudo-direct addressing mode. 4. R Opcode(6 Rs(5) Rt(5) Rd(5) Shamt5)...

Q:

Provide a summary technical report with your own words about Pipelined Execution which is also named as Instruction Level Parallelism, addressing mainly the following areas: 1. What is Pipelined...

Q:

PART 1 1.1 Incremental Building From a design perspective, you should build and test your processor incrementally. This means building one small part and testing that it behaves the way you want...

Q:

54 Say we have a memory consisting of 1024 locations, and each location contains 8 (a) How many bits are required for the address? If we use the PC-relative addressing mode, and want to allow control...

Q:

ITEC1000A3 1) [15 points] Assume 32 different op codes and 15-bit instruction word in a computer system.Four bits in the instruction are reserved to indicate the addressing mode. (a) Draw a box style...

Q:

pts 1. (a) True or False. Immediate addressing mode implies that all operands are in registers (b) True or False. In PC relative addressing the offset cannot be negative. True or False. In the von...

Q:

3.1 New LC-3 Instructions As you know, in the LC-3, values can be stored in system memory (RAM), and copied from there to the eight general purpose registers named RO through R7, or in several...

Q:

please read carefully and each exercise is its own code. start with .orig x3000 3.1 New LC-3 Instructions As you know, in the LC-3, values can be stored in system memory (RAM), and copied from there...

Q:

Objectives: - Designing a Single-Cycle Processor with 16-bit instructions and 16-bit registers - Using the Logisim simulator to model and test the processor - Teamwork Instruction Set Architecture In...

Q:

Please explain solution as well! Thank you! Format Design for a modified MIPS-Lite ISA Instruction Set Architecture) Design the instruction formats for a version of the MIPS-Lite insiruction set...

Q:

You take a new position as an accountant. During your first week of work, you notice the company has one employee that is in charge of the ordering of merchandise, receiving the merchandise when it...

Q:

The new coordinates (X,, Y,) of a point in the x-y plane that is rotated about the z axis at an angle e (positive is clockwise) are given by Xr, = X0cos- Y0sin Yr, = X0sin + Y0cos where (X0, Y0) are...

Q:

Chip & Dale, Inc. makes an adjusting entry at the end of the accounting period on investments it owns. As a result, it will show which account on its balance sheet? Multiple choice question. Interest...

Q:

gpt 1 2 9 .

Q:

Go to the website of the Federal Reserve Bank of St. Louis (http://www.stlouisfed.org) to find some information about the Fed. Find a map of the Federal Reserve districts. If you live in the United...

Q:

Suppose that the T-account for First National Bank is as follows: Assets Liabilities Reserves $100,000 Deposits $500,000 Loans 400,000 a. If the Fed requires banks to hold 5 percent of deposits as...

Q:

Imagine that you intend to buy a portfolio of ten stocks with some of your savings. Should the stocks be of companies in the same industry? Should the stocks be of companies located in the same...