Question: In an orthogonal cutting operation, the tool has a rake angle = of 15. The chip thickness before the cut = 0.30 mm and the

  •  In an orthogonal cutting operation, the tool has a rake angle = of 15°. The chip thickness before the cut = 0.30 mm and the cut yields a deformed chip thickness = 0.65 mm. 
  • Calculate (a) the shear plane angle and (b) the shear strain for the operation.  

Step by Step Solution

★★★★★

3.45 Rating (168 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Solution Q chip thickness For shear Plane Angle Goven Rake angle ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

In an orthogonal cutting test the following conditions were noted: width chip(width of cut) = 2.5mm unreformed chip thickness = 0.25mm chip thickness = 1 mm working normal rake = -5 degrees cutting...

Q:

A square silicone chip 7 mm by 7 mm in size and 0.5 mm thick is mounted on a plastic substrate with its front surface cooled by a synthetic liquid flowing over it. Electronic circuits in the back of...

Q:

A slab of copper of thickness b = 2.00 mm is thrust into a parallel plate capacitor of plate area A = 2.40 cm2 and plate separation d = 5.00 mm, as shown in Figure the slab is exactly between the...

Q:

An orthogonal cutting operation is being carried out under the following conditions: to = 0 . 1 mm , tc = 0 . 2 mm , width of cut = 5 mm , V = 2 m / s , rake angle = 1 0 0 , Fc = 5 0 0 N , and Ft = 2...

Q:

The beam is made from three polystyrene strips that are glued together as shown. If the glue has shear strength of 80 kPa, determine the maximum load P that can be applied without causing the glue to...

Q:

Calculate the torque N twisting a steel tube of length l = 3.0 m through an angle = 2.0 about its axis, if the inside and outside diameters of the tube are equal to d1 = 30 mm and d2 = 50 mm.

Q:

A copper-bottomed saucepan containing 0.8 L of boiling water boils dry in 10 min. Assuming that all the heat flows through the flat copper bottom, which has a diameter of 15 cm and a thickness of 3.0...

Q:

Suppose that on any given day the annualized continuously compounded stock return has a volatility of either 15%, with a probability of 80%, or 30%, with a probability of 20%. This is a mixture of...

Q:

Suppose that on any given day the annualized continuously compounded stock return has a volatility of either 15%, with a probability of 80%, or 30%, with a probability of 20%. This is a mixture of...

Q:

Gear A has a mass of 1 kg and a radius of gyration of 30 mm; gear B has a mass of 4 kg and a radius of gyration of 75 mm; gear C has a mass of 9 kg and a radius of gyration of 100 mm. The system is...

Q:

Your supervisor, Heather, has a number of clients in the fruit and farming industry. The clients are Raspberry Limited, Sour Grapes Pty Ltd, Bouncing Berries Pty Ltd and Lemon Zest Limited. Raspberry...

Q:

My uncle borrowed 5,000 bolivars (B5,00) from his brother in Caracas, Venezuela. He promised to repay the loan in two annual installments of B3,000 each. What rate of interest is he paying his...

Q:

Which Excel auditing tool helps identify which cells influence a selected formula?

Q:

In what way does our trade model represent a general equilibrium model? In what way does it not? In what ways does our trade model require further extension?

Q:

What does an improvement in a nations terms of trade mean? What effect does this have on the nations welfare?

Q:

What do the terms of trade measure? What is the relationship between the terms of trade in a world of two trading nations? How are the terms of trade measured in a world of more than two traded...

Q:

Under what condition will trade take place at the pre-trade-relative commodity price in one of the nations?

Q:

Why does the use of demand and supply curves of the traded commodity refer to partial equilibrium analysis? In what way is partial equilibrium analysis of trade related to general equilibrium...

Q:

Determine algebraically whether the given function is even, odd, or neither. f left parenthesis x right parenthesis equals negative 9 x cubed

Q:

What are the three primary phases of product design, and how does the consideration of materials differ in each?

Q:

How can cross-linking be used to control the engineering properties of elastomers?

Q:

Why are multiple coats or layers put on the carbide base for coated tools?

Q:

No Leak Plumbing and Repair provides customers with firm quotes for a plumbing repair job before actually starting the job. To be able to do this, No Leak has been very careful to maintain time...

Q:

According to Business Week, Maternity Chic, a purveyor of designer maternity wear, sells dresses and pants priced around $150 each for an average total sale of $1,200. The total sale has a normal...

Q:

USA Todays annual survey of public flagship universities (Arienne Thompson and Breanne Gilpatrick, Double-Digit Hikes Are Down, October 5, 2005) indicates that the median increase in in-state tuition...