Question: It is required to design a chain drive with a duplex chain to connect a 1 5 kW , 1 4 4 0 rpmelectric motor

It is required to design a chain drive with a duplex chain to connect a 15 kW,1440 rpmelectric motor to a transmission shaft running at 350 rpm. The operation involves themoderate shocks.(i) Specify the number of teeth on the driving and driven sprocket.(ii) Select proper roller chain.(iii) Calculate the pitch circle diameters of the driving and driven sprockets.(iv) Determine the number of chain links.(v) Specify the correct center distance.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

The horizontal wye fitting in Fig P3.173 splits the 20°C water flow rate equally, if Q1 = 5 ft3/s and p1 = 25 lbf/in2 (gage) and losses are neglected, estimate (a) p2, (b) p3, and (c) the vector...

Q:

1. It is required to design a chain drive to connect a 18.5kW motor running at 725rpm to a gear pump operating at 400rpm. The approximate centre distance between the motor and pump is 470mm (i)...

Q:

Hello, you already did chapter 1 and 2 of my MASTERS Thesis already for me. (See attached) So normally you know masters thesis consist of 5 chapters right ??..... But in this case my thesis will be 4...

Q:

PUTEX CORPORATION: CORPORATE PLANNING PROCESS It was early morning of Monday, March 24, 2014, Gupta was driving to his office located on outskirts of the city. His mind was totally occupied with the...

Q:

Review an Annual Report to gain a general understanding of the types of financial information contained in the report and why that information might be useful to a potential reader. You will also be...

Q:

512 CHAPTER 16 Organizational Culture Like every major CEO, Burns is a millionaire. Yet she still shops for groceries. She drives herself to work. She cleans her own house. \"Where you are is not who...

Q:

Task: It is required to design and configure a computer network for a university campus. The design will depend on classless addressing, and it will support static routing. You will design the...

Q:

KINGS OWN INSTITUTE* Success in Higher Education ICT106 DATA COMMUNICATIONS AND NETWORKS T223 Page 1 of 18 AUSTRALIAN INSTITUTE OF BUSINESS AND MANAGEMENT PTY LTD ABN: 72 132 629 979 CRICOS 03171A...

Q:

U.S. Department of Transportation Federal Aviation Administration Subject: RUNWAY LENGTH REQUIREMENTS FOR AIRPORT DESIGN Advisory Circular Date: 7/1/2005 Initiated by: AAS-100 AC No: 150/5325-4B...

Q:

Part I: Answer each question thoroughly, read over each problem, discuss the pros and cons of each option, and select the best option including your justification and your own opinion. H & I Advanced...

Q:

Pleases design below by using Cadence tool.. Coursework Assignment: Full Custom Design of a Digital to Analogue Converter (DAC) in 90nm/45nm CMOS Department of Electrical and Electronic Engineering...

Q:

A person borrows $200 to be repaid in 8 years with 14% annually compounded interest. The loan may be repaid at the end of any earlier year with no prepayment penalty. a. What amount will be due if...

Q:

Quantitative Problem 2: Hadley Inc. forecasts the year-end free cash flows (in millions) shown below. Year 1 2 3 4 5 FCF -$22.91 $38.1 $43.6 $52.2 $55.4 The weighted average cost of capital is 10%,...

Q:

A hair product manufacturer offers the following information: WIP Inventory, January 1 0 units Units started 29,600 units Units completed and transferred out 11,200 units WIP Inventory, December 31...

Q:

) Topic: Recording of transaction in the Cash Receipt Journal of a Trading business. Activity 6: The Cash Receipt Journal of a Trading business. (Class activity) 1. What does the acronym CRJ stand...