Question: Live snow load = 2 5 psf Dead load: ( 1 ) Roof and Sheathing = 1 6 p s f , ( 2 )

Live snow load =25 psf
Dead load: (1) Roof and Sheathing =16psf,(2) Rafters =4lbft
Roof pitch: 5:12
Please round to the nearest one tenth (i.e.,0.1).
Total load (LL+DL) on a middle rafter after adjusting to horizontal projection =
lbft
Live snow load = 2 5 psf Dead load: ( 1 ) Roof

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

13. What is the purpose of a design review? 14. Why is it important to have a good mix of skills in a design review panel? 15. What does the schematic design stage entail, including management roles...

Q:

Final Estimating Project You are employed by a contactor that is replying to a tender for a small garage project in a small township in Northern Ontario. Your assignment is to compete an estimate of...

Q:

2. (10pts) A house roof has #1 DFL dimension lumber roof rafters in the roof that span 13.25' from the sidewall to a ridge beam. The roof pitch is 8:12 and the rafters are 2'o-c. Assume that the roof...

Q:

1. A ridge beam 1 ft wide by 2 ft deep in a roof system carries beams which are 36 in. apart o.c. The roof carries a uniform dead load in the direction of gravity of 30 psf (along the inclined...

Q:

The Pratt roof trusses are uniformly spaced every 15 ft. The deck, roofing material, and purlins have an average weight of 5.6 psf. The building is located in New York where the anticipated snow load...

Q:

Live load = 40 psf Dead load: (1) Slab = 50 psf, (2) Deck = 5 psf, (3) Mechanical equipment = 13 psf, (4) Suspended ceiling = 8 psf, (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft Beam and Girder...

Q:

Estimate the forces in the diagonals used in the tower to support the cantilevered areas and the forces in the beam directly supported by the diagonals. This requires tracing the loads through the...

Q:

The structural system for the metal building shown below consists of gabled frames spaced at 25'-0" on center. Each gabled frame is assembled from a roof truss supported by a column at each end. The...

Q:

Scope: Using plans and specifications provided to you, come up with a design concept and do a preliminary design for your project. For this, you will need: -To calculate loading: both environmental...

Q:

The floor sheathing in a corridor of a building is to be sized for dead plus live load and span/240 deflection criterion. 4-ply sheathing (stress parallel to the strength axis) is to be used over...

Q:

A square flat plate is 1.5 m by 1.5 m. Its two surfaces are maintained at 120 C. The plate convects from its two surfaces to the room air which is at 20 C. (a) What is the rate of heat transfer to...

Q:

Rodamex Inc. reported the following summary transactions during the year ended December 31, 2015: a. Sold merchandise for $ 5,000,000, including $ 500,000 cash and $ 4,500,000 on account, with terms...

Q:

Which modern financial innovation was inspired by the 2 0 0 8 financial crisis? Group of answer choices Centralized banking Bitcoin The Euro The Federal Reserve

Q:

Arnez Company's annual accounting period ends on December 31. The following information concerns the adjusting entries to be recorded as of that date. a. The Office Supplies account started the year...