Methanol (CH3OH) is a key raw material for many chemical products and has potential as a...
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
Methanol (CH3OH) is a key raw material for many chemical products and has potential as a transport fuel. According to the Methanol Institute [1], the annual global production is currently around 65 million metric tonnes (Mta). In a report by IRENA [2], approximately 70% of the methanol produced worldwide is used in chemical syntheses. The following products (in order of quantity of methanol consumed) are: Formaldehyde, methyl tert-butyl ether (MTBE), acetic acid, dimethyl ether (DME), propene, methyl methacrylate and dimethyl terephthalate (DMT). However, there are many more that are produced from methanol to a lesser extent. More than 95% of methanol currently produced comes from natural gas. However, methanol may be produced from carbon sources, and therefore there is also strong potential for it to play an important role in reducing carbon footprint of our society. There is clearly a need to produce many of the products currently made using methanol with a smaller carbon footprint. Methanol can also play an important role in diesel fuel substitutes. Methanol is a significant feedstock in the manufacture of biodiesel. In addition, the methanol derivative dimethyl ether (DME) is regarded as an ideal substitute for diesel in most diesel engines, Volvo [3] and even if this was to occur at a small fraction of the global diesel consumption (720Mta), this would increase significantly the global methanol production. According to IRENA [2], methanol can be blended directly with gasoline up to 20 vol%, but it is more frequently converted to MTBE. Methanol Synthesis The conventional method of producing methanol on a large scale is by steam reforming natural gas as shown in Figure 1. CH4 + H2O CO + 3H AH = 206 kJ mol-1 The methanol synthesis proceeds via two reactions simultaneously CO2H2CH3OH AH -98 kJ mol-1 CO2 + 3H2 CHOH + HO AH = -58 kJ mol-1 (1) (2) (3) The mismatch in the H2/CO ratio between the reforming (reaction 1) and synthesis section (reaction 2) leads to different options in the plant design, which include steam-only reforming, CO or "dry" reforming, and auto-thermal reforming (which involves partial oxidation). In order not to waste H, the molar ratio of H2 to CO should be just above 2.0 going into the methanol synthesis loop. Using reaction (3), methanol can also be produced from Hz and CO2. If H2 is available from a carbon neutral process and CO2 can be captured as a waste stream and reused, the methanol produced would be carbon neutral, providing that any other utilities can also be provided with no net CO2 emissions. In this project you will be developing a Process Flow Diagram for methanol production from CO captured from point sources (flue gas) or Direct Air Capture (DAC) and green hydrogen (H2 produced from electrolysis of water). Alternatively, methanol can also be produced from carbon derived from biological sources, such as biomass. There are two pathways for converting biomass into methanol feedstock. First is the gasification route, in which solid biomass containing approximately 10 wt% moisture or lower is gasified in oxygen deficient conditions to produce synthesis gas (a mixture of mainly CO, CO and H), which can be fed to the methanol synthesis process. The second route is anerobic fermentation, in which biomass containing approximately 30 wt% moisture or more is digested in a bioreactor to produce biogas (a mixture of mainly CO2 and CH4), which can be upgraded via dry- or bi- reforming to make synthesis gas. Dry reforming of methane is show in reaction (4), whereas bi-reforming is a combination of dry reforming and steam reforming (reactions (1) and (4) combined). CH4 + CO 2CO + 2H2 AH = 247.3 kJ mol-1 (4) Process water Process fuel Natural gas Steam Process fuel Electricity Cooling water Catalysts: CoMo, NiMo, ZnO, CuO, A1203 production Heat recovery Purge gas Hydrogen Light ends Synthesis gas Raw methanol Steamreforming Methanol synthesis Methanol purification Methanol, at plant Sulphur from desulphurisation Emission to air CO, CO2, NOX, VOC Spent catalysts Waste heat Waste water Figure 1: Simplified Process Flow Diagram for a natural gas based methanol plant (from [4]) Part 1.A 26 Marks In the first assignment (Mass Balances) you will conduct "hand-calculation" of feedstock preparation and methanol synthesis route. Biomass (sugarcane bagasse) is gasified in a novel Reactive Flash Volatilisation (RFV) process to produce synthesis gas, along with biochar and water-soluble tar as by- products. In a pilot plant RFV process, pulverised biomass is feed to catalytic gasifier at a rate of 10.0 kg/h, along with 4.2 L(STP)/h of O2 and 6.4 kg/h of steam as the gasifying agents. The biomass and oxygen are supplied at room temperature, whereas the steam is fed at 150C and the gasifier operates at 800C. The steam is supplied in excess; therefore, the unreacted water vapour exiting the gasifier with the synthesis gas is condensed at room temperature before the synthesis gas is sent for further processing. The condensed water can be assumed to contain all of the water-soluble tar produced in the gasifier. The biochar is periodically drawn from the gasifier and sent for analysis. Table 1 provides the ultimate and proximate analysis of sugarcane bagasse, whereas Table 2 shows the raw data for synthesis gas flow rate (wet basis) and composition (nitrogen and water free basis) measured at the outlet of the condenser. Table 3 provides the ultimate analysis of char and tar collected from the gasifier and condenser, respectively. 1. Conduct an atom species balance for C, N, H and O for the duration of the given measurement and estimate the average carbon conversion efficiency (percentage of carbon conversion into gas phase). (18 Marks) 2. Report the errors in mass balance analysis and reflect upon the reasons for those errors. What could be the reasons behind mass balances not closing properly? (8 Marks) Table 1 - Proximate and Ultimate Analysis of Sugarcane Bagasse Ultimate Analysis (% db) Carbon (C) 46.40 Hydrogen (H) 6.19 Nitrogen (N) 0.44 Sulphur (S) 0.05 Oxygen (O) a Proximate Analysis Moisture 44.42 (% as received, db except moisture) Ash Volatile Matter Fixed Carbon a Calculated by difference. 10.0 2.5 79.16 18.13 Table 2 - Time on stream gas measured flow rate and composition Time on Synthesis gas flow Synthesis gas composition (mol fraction) Stream rate (min) (Nm/h)* CO2 H2 CH4 CO SO2 30 15.89 0.321 0.474 0.024 0.186 N.D. 60 15.94 0.355 0.471 0.023 0.155 N.D. 90 15.66 0.275 0.503 0.034 0.188 N.D. 120 16.61 0.346 0.488 0.025 0.149 N.D. 150 16.46 0.409 0.438 0.022 0.132 N.D. 180 14.61 0.306 0.497 0.034 0.164 N.D. 210 16.70 0.322 0.480 0.034 0.165 N.D. 240 15.88 0.348 0.469 0.031 0.153 N.D. 270 14.82 0.319 0.480 0.041 0.162 N.D. 300 13.75 0.334 0.478 0.033 0.158 N.D. 330 16.51 0.320 0.474 0.038 0.171 N.D. 360 16.22 0.307 0.470 0.042 0.183 N.D. 390 15.66 0.367 0.459 0.031 0.144 N.D. 420 16.75 0.375 0.490 0.030 0.130 N.D. 450 15.66 0.375 0.498 0.034 0.149 N.D. 480 14.48 0.381 0.527 0.039 0.158 N.D. 510 16.13 0.367 0.466 0.032 0.149 N.D. 540 15.21 0.366 0.519 0.044 0.181 N.D. 570 13.75 0.381 0.499 0.036 0.147 N.D. 600 12.25 0.421 0.414 0.032 0.131 N.D. Normal conditions = 25C, 1 atm Table 3 - Ultimate analysis of biochar and tar Sample Yield Composition (wt%) name (kg/h) N C H S Biochar 0.262 0.472 50.833 0.419 N.D. Tar 1.552 0.794 0.243 7.458 N.D. Part 1.B 26 Marks The synthesis gas produced from the RFV process is pretreated to make the feed for methanol synthesis process. The pretreated synthesis gas feed enters the methanol synthesis plant at a flow rate of 100.0 kmol/h and contains 1.0% methane (inert) with the remainder being a stoichiometric mixture of CO and H2. This stream is mixed with a recycle stream to produce a stream which is fed to the reactor. The product of the reactor is at equilibrium conversion based on reaction (2) and enters a condenser which condenses some of the methanol. The overhead gas product contains 5.0 mol% methane, 5.0% methanol, 30.0% CO and the remaining H2. 5.0% of the overhead gas is purged to prevent build-up of the methane and the rest is recycled. The liquid product from the condenser contains pure methanol. A. Draw and clearly label the block flow diagram. Calculate the following - B. The molar flow rate of the purge stream. C. The molar flow rate of the liquid methanol stream. D. The equilibrium constant K based on the mole fractions. E. The composition of the recycle stream on a mass basis. F. The overall and single pass fractional conversion of CO in the reactor. (4 Marks) (3 Marks) (3 Marks) (10 Marks) (3 Marks) (3 Marks) Methanol (CH3OH) is a key raw material for many chemical products and has potential as a transport fuel. According to the Methanol Institute [1], the annual global production is currently around 65 million metric tonnes (Mta). In a report by IRENA [2], approximately 70% of the methanol produced worldwide is used in chemical syntheses. The following products (in order of quantity of methanol consumed) are: Formaldehyde, methyl tert-butyl ether (MTBE), acetic acid, dimethyl ether (DME), propene, methyl methacrylate and dimethyl terephthalate (DMT). However, there are many more that are produced from methanol to a lesser extent. More than 95% of methanol currently produced comes from natural gas. However, methanol may be produced from carbon sources, and therefore there is also strong potential for it to play an important role in reducing carbon footprint of our society. There is clearly a need to produce many of the products currently made using methanol with a smaller carbon footprint. Methanol can also play an important role in diesel fuel substitutes. Methanol is a significant feedstock in the manufacture of biodiesel. In addition, the methanol derivative dimethyl ether (DME) is regarded as an ideal substitute for diesel in most diesel engines, Volvo [3] and even if this was to occur at a small fraction of the global diesel consumption (720Mta), this would increase significantly the global methanol production. According to IRENA [2], methanol can be blended directly with gasoline up to 20 vol%, but it is more frequently converted to MTBE. Methanol Synthesis The conventional method of producing methanol on a large scale is by steam reforming natural gas as shown in Figure 1. CH4 + H2O CO + 3H AH = 206 kJ mol-1 The methanol synthesis proceeds via two reactions simultaneously CO2H2CH3OH AH -98 kJ mol-1 CO2 + 3H2 CHOH + HO AH = -58 kJ mol-1 (1) (2) (3) The mismatch in the H2/CO ratio between the reforming (reaction 1) and synthesis section (reaction 2) leads to different options in the plant design, which include steam-only reforming, CO or "dry" reforming, and auto-thermal reforming (which involves partial oxidation). In order not to waste H, the molar ratio of H2 to CO should be just above 2.0 going into the methanol synthesis loop. Using reaction (3), methanol can also be produced from Hz and CO2. If H2 is available from a carbon neutral process and CO2 can be captured as a waste stream and reused, the methanol produced would be carbon neutral, providing that any other utilities can also be provided with no net CO2 emissions. In this project you will be developing a Process Flow Diagram for methanol production from CO captured from point sources (flue gas) or Direct Air Capture (DAC) and green hydrogen (H2 produced from electrolysis of water). Alternatively, methanol can also be produced from carbon derived from biological sources, such as biomass. There are two pathways for converting biomass into methanol feedstock. First is the gasification route, in which solid biomass containing approximately 10 wt% moisture or lower is gasified in oxygen deficient conditions to produce synthesis gas (a mixture of mainly CO, CO and H), which can be fed to the methanol synthesis process. The second route is anerobic fermentation, in which biomass containing approximately 30 wt% moisture or more is digested in a bioreactor to produce biogas (a mixture of mainly CO2 and CH4), which can be upgraded via dry- or bi- reforming to make synthesis gas. Dry reforming of methane is show in reaction (4), whereas bi-reforming is a combination of dry reforming and steam reforming (reactions (1) and (4) combined). CH4 + CO 2CO + 2H2 AH = 247.3 kJ mol-1 (4) Process water Process fuel Natural gas Steam Process fuel Electricity Cooling water Catalysts: CoMo, NiMo, ZnO, CuO, A1203 production Heat recovery Purge gas Hydrogen Light ends Synthesis gas Raw methanol Steamreforming Methanol synthesis Methanol purification Methanol, at plant Sulphur from desulphurisation Emission to air CO, CO2, NOX, VOC Spent catalysts Waste heat Waste water Figure 1: Simplified Process Flow Diagram for a natural gas based methanol plant (from [4]) Part 1.A 26 Marks In the first assignment (Mass Balances) you will conduct "hand-calculation" of feedstock preparation and methanol synthesis route. Biomass (sugarcane bagasse) is gasified in a novel Reactive Flash Volatilisation (RFV) process to produce synthesis gas, along with biochar and water-soluble tar as by- products. In a pilot plant RFV process, pulverised biomass is feed to catalytic gasifier at a rate of 10.0 kg/h, along with 4.2 L(STP)/h of O2 and 6.4 kg/h of steam as the gasifying agents. The biomass and oxygen are supplied at room temperature, whereas the steam is fed at 150C and the gasifier operates at 800C. The steam is supplied in excess; therefore, the unreacted water vapour exiting the gasifier with the synthesis gas is condensed at room temperature before the synthesis gas is sent for further processing. The condensed water can be assumed to contain all of the water-soluble tar produced in the gasifier. The biochar is periodically drawn from the gasifier and sent for analysis. Table 1 provides the ultimate and proximate analysis of sugarcane bagasse, whereas Table 2 shows the raw data for synthesis gas flow rate (wet basis) and composition (nitrogen and water free basis) measured at the outlet of the condenser. Table 3 provides the ultimate analysis of char and tar collected from the gasifier and condenser, respectively. 1. Conduct an atom species balance for C, N, H and O for the duration of the given measurement and estimate the average carbon conversion efficiency (percentage of carbon conversion into gas phase). (18 Marks) 2. Report the errors in mass balance analysis and reflect upon the reasons for those errors. What could be the reasons behind mass balances not closing properly? (8 Marks) Table 1 - Proximate and Ultimate Analysis of Sugarcane Bagasse Ultimate Analysis (% db) Carbon (C) 46.40 Hydrogen (H) 6.19 Nitrogen (N) 0.44 Sulphur (S) 0.05 Oxygen (O) a Proximate Analysis Moisture 44.42 (% as received, db except moisture) Ash Volatile Matter Fixed Carbon a Calculated by difference. 10.0 2.5 79.16 18.13 Table 2 - Time on stream gas measured flow rate and composition Time on Synthesis gas flow Synthesis gas composition (mol fraction) Stream rate (min) (Nm/h)* CO2 H2 CH4 CO SO2 30 15.89 0.321 0.474 0.024 0.186 N.D. 60 15.94 0.355 0.471 0.023 0.155 N.D. 90 15.66 0.275 0.503 0.034 0.188 N.D. 120 16.61 0.346 0.488 0.025 0.149 N.D. 150 16.46 0.409 0.438 0.022 0.132 N.D. 180 14.61 0.306 0.497 0.034 0.164 N.D. 210 16.70 0.322 0.480 0.034 0.165 N.D. 240 15.88 0.348 0.469 0.031 0.153 N.D. 270 14.82 0.319 0.480 0.041 0.162 N.D. 300 13.75 0.334 0.478 0.033 0.158 N.D. 330 16.51 0.320 0.474 0.038 0.171 N.D. 360 16.22 0.307 0.470 0.042 0.183 N.D. 390 15.66 0.367 0.459 0.031 0.144 N.D. 420 16.75 0.375 0.490 0.030 0.130 N.D. 450 15.66 0.375 0.498 0.034 0.149 N.D. 480 14.48 0.381 0.527 0.039 0.158 N.D. 510 16.13 0.367 0.466 0.032 0.149 N.D. 540 15.21 0.366 0.519 0.044 0.181 N.D. 570 13.75 0.381 0.499 0.036 0.147 N.D. 600 12.25 0.421 0.414 0.032 0.131 N.D. Normal conditions = 25C, 1 atm Table 3 - Ultimate analysis of biochar and tar Sample Yield Composition (wt%) name (kg/h) N C H S Biochar 0.262 0.472 50.833 0.419 N.D. Tar 1.552 0.794 0.243 7.458 N.D. Part 1.B 26 Marks The synthesis gas produced from the RFV process is pretreated to make the feed for methanol synthesis process. The pretreated synthesis gas feed enters the methanol synthesis plant at a flow rate of 100.0 kmol/h and contains 1.0% methane (inert) with the remainder being a stoichiometric mixture of CO and H2. This stream is mixed with a recycle stream to produce a stream which is fed to the reactor. The product of the reactor is at equilibrium conversion based on reaction (2) and enters a condenser which condenses some of the methanol. The overhead gas product contains 5.0 mol% methane, 5.0% methanol, 30.0% CO and the remaining H2. 5.0% of the overhead gas is purged to prevent build-up of the methane and the rest is recycled. The liquid product from the condenser contains pure methanol. A. Draw and clearly label the block flow diagram. Calculate the following - B. The molar flow rate of the purge stream. C. The molar flow rate of the liquid methanol stream. D. The equilibrium constant K based on the mole fractions. E. The composition of the recycle stream on a mass basis. F. The overall and single pass fractional conversion of CO in the reactor. (4 Marks) (3 Marks) (3 Marks) (10 Marks) (3 Marks) (3 Marks)
Expert Answer:
Related Book For
Posted Date:
Students also viewed these chemical engineering questions
-
Identify the process evaluation article that you chose and explain why you selected this example. Describe the purpose of the evaluation, the informants, the questions asked, and the results of the...
-
The Canadian Bankers Association is pleased to provide this submission in response to Finance Canada's January 2019 consultation paper (the Consultation Paper) on the merits of open banking in...
-
Suppose that Q(x, y) is a function such that 1/Q(x, y) is continuous for all (x, y). Which of the following statements are true? (a) Q(x, y) is continuous for all (x, y). (b) Q(x, y) is continuous...
-
Develop a table of outcomes similar in format in the text. The entries will be the probabilities of the various possible outcomes in the inspection operation.
-
On January 1, 2024, the Merit Group issued to its bank a $41 million, five-year installment note to be paid in five equal payments at the end of each year. Installment payments of $10 million...
-
The average pressure and shear stress acting on the surface of the 1-m-square flat plate are as indicated in Fig. P9.4. Determine the lift and drag generated. Determine the lift and drag if the shear...
-
Yount Co. has equipment that cost $50,000 and that has been depreciated $22,000. Record the disposal under the following assumptions. (a) It was scrapped as having no value. (b) It was sold for...
-
You, CPA, as the Senior Auditor for the MMC financial statement audit engagement for the year ended March 31, 2020 met with the Audit Partner prior to beginning audit fieldwork. The Audit Partner has...
-
Provide an example of a marine shipment, covering the premium, and total insurance value.
-
Why is the effect of persuasive communication so great/ or play a important role in the field of business administration?
-
dimensionality of service perspective under digital transformation. Critically analyze services as deeds, processes, and performances from the perspective of time-perishable, intangible experience...
-
1) Your borrowed $250,000 on Jan 1st 2022. The annual interest rate is 5.4% . The monthly payment is $2500. You pay $1250 extra every 3rd month (that is, month 3, 6, 9, . . .) . What will be your...
-
A budget is a plan that people made for their self to show them how much money they can spend to stay within their budget goals. Revenue is the total amount of money that is made over a set amount of...
-
Larry purchases a $100 perpetuity. The payments on the annuity begin in one year, and the appropriate interest rate is 10%. What is the present value of Larry's payments that will occur from year 31...
-
What is some information that should be found in big data databases? Why has big-data analytics become so popular with companies like kraft foods, united airlines, and ford motor company? How do you...
-
Uniform electric field in Figure a uniform electric field is directed out of the page within a circular region of radius R = 3.00 cm. The magnitude of the electric field is given by E = (4.50 x 10-3...
-
(a) Is the magnitude of the gravitational force exerted by Earth on a ball greater than, equal to, or smaller than the magnitude of the gravitational force exerted by the ball on Earth? (b) Is the...
-
Two objects 1 and 2, of mass \(m_{1}\) and \(m_{2}\), are released from rest far from Earth, at a location where the magnitude of the acceleration due to gravity is much less than \(g=9.8 \mathrm{~m}...
-
A communications satellite orbits \(1.4 \times 10^{7} \mathrm{~m}\) from Earth's center, at a location where the magnitude of Earth's gravitational field is \(2.0 \mathrm{~N} / \mathrm{kg}\). (a) If...
Study smarter with the SolutionInn App