Question: Problem 4 . The beam shown in below is under distributed dead load of 2 kip s f t and point live loads of 5

Problem 4. The beam shown in below is under distributed dead load of 2kipsft and point live loads of 50 kips. The beam top flange is connected to concrete slab and has full lateral support. Find the lightest W shape to carry the given load considering only flexural limit state. Use A992 Grade 50 steel .
Problem 4 . The beam shown in below is under

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

A = 2 B = 2 C = 5 D = 1 Problem #4 A concentrated live of 25 kips and distributed live load of 3 kips/ft can be placed anywhere on the beam, determine the maximum positive shear force at C and...

Q:

The building frame shown below has a single 40 ft long continuous beam A-B. The beam experiences an evenly distributed dead load of 1.0 kip/ft (including self-weight). Columns are evenly spaced at 10...

Q:

The point loads are placed at the fixed positions shown in the figure and they are live loads. A k a b a 1 B * Asc Ast Cross section 1 W C (centre) 'c= = 38 Mpa f'ct.f = 3.5 MPa fsy = 500 MPa E = 200...

Q:

1. Draw the shear and bending moment diagrams and find the deflection for a cantilever beam of length 15 ft. with a uniformly distributed dead load of 1.5 kip/ft (in addition to its own weight) and a...

Q:

The beam shown in Figure 2.1 is supported by a fixed support at point C and a roller at point A. It also has an internal hinge at point B. The beam supports a point load at point D, a moment at point...

Q:

I would highly appreciate it if you would help me with this question pl 2. A two story building has a floor framing plans as shown below. As directed on the following pages calculate the unfactored...

Q:

LEVEL 3 DESIGN LOADS - WEST WING LOAD SDL LIVE LIVE CONCENTRICA PARTITIONS kN/m2 PSF DENOTED ON PLAN AREA kN/m2 PSF kN/m2 PSF KN KIPS 0.75 2.50 53 7.20 150 9.00 2 SLABS STAIRS ESCALATOR P1 15 15 0.75...

Q:

Design Beam D. 1. You will need to compute the dead and live loads distributed on the edge beam. These come from the slab, self-weight of the edge beam, and the 200 lb/ft dead load. The slab is...

Q:

I POSTED THIS QUESTION BEFORE BUT I WAS ASKED TO PROVIDE MORE INFORMATION. IN WHICH PART DO I NEED TO PROVIDE MORE INFORMATION SO THAT I CAN POST THAT AS WELL?? The plans & elevations are for a...

Q:

The instantaneous (short-term) deflections and long-term deflection are being investigated for the simply supported beam shown in Figure 2. This beam supports a dead load (including the beam...

Q:

The balance sheet for Focus Consulting reports the following information on July 1,2012. Focus decides to redeem these bonds at 101 after paying semiannual interest. Prepare the journal entry to...

Q:

a. 2* 10^5 N/mm^2 b. 3* 10^5 N/mm^2 c. 4* 10^5 N/mm^2 d. 6* 10^5 N/mm^2 Q.11 A rod of steel 60 mm wide and 15 mm thick is 8 meters long. It extends by 5.31 mm when an axial pull of 120 kN is applied....

Q:

Solve for the Volatility for Cola Co . and for Gas Co . The following spreadsheet contains monthly returns for Cola Co . and Gas Co . for 2 0 2 2 : Using these data, estimate the average monthly...

Q:

Problem 1: On August 31, 2021, DASHER Company issued at 104 plus accrued interest, three thousand 10% bonds with a face amount of ?1,000 per bond. The bonds are dated April 1, 2021, mature on March...