Question: PROBLEM 5 A simple gear train has 2 spur gears. The input gear has 2 0 teeth and the output gear has 1 0 0

PROBLEM 5 A simple gear train has 2 spur gears. The input gear has 20 teeth and the output gear has 100 teeth. The input rotates at 2000 rpm clockwise. Calculate the gear ratio and the output speed. he input torque is 15 Nm and the efficiency is 65%. Calculate the output power and the holding torque.
PROBLEM 5 A simple gear train has 2 spur gears.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A simple gear train has 2 spur gears. The input gear has 15 teeth and the output gear has 93 teeth. The input rotates at 100 rev/min clockwise, with an input torque of 28 Nm, and the overall...

Q:

Figure Q3 shows a gear train of straighttooth spur gears from input Gear 2 to output Gear 8. Gear 2 is run by a 1 hp and rotates at 1800 rpm. Gear 8 rotates at 900 rpm. The gears have diametral pitch...

Q:

The countershaft in Prob. 373, p. 138, is part of a speed reducing compound gear train using 20 spur gears. A gear on the input shaft drives gear A with a 2 to 1 speed reduction. Gear B drives a gear...

Q:

Gear 2 4. (15 points) The two-stage simple gear train has Gear 2 as the input and Gear 5 as the output. If Gear 2 has 12 teeth, Gear 3 has 24 teeth and Gear 4 has 12 teeth, and Gear 5 has 18 teeth....

Q:

The countershaft shown in figure (a) below, is part of a speed reducing compound gear train using 20 spur gears (see figure (c) Gear-C on the input shaft-a drives gear-A with a 2 to 1 speed...

Q:

The countershaft in Prob. 372, p. 138, is part of a speed reducing compound gear train using 20 spur gears. A gear on the input shaft drives gear A. Gear B drives a gear on the output shaft. The...

Q:

Design the following gear trains. Label each gear with the number of gear teeth. In each case show clear top and front view diagrams approximately to scale wherever possible. 1. A simple gear train...

Q:

In the figure below, a compression loading frame is illustrated. The power generated by the electrical motor of uniform supply is transmitted through the planetary gear box, worm, worm gear and spur...

Q:

You are to design a power transmission system for a wind turbine. The input is a wind turbine whose torque input is assumed at 34 N-m at 250 rpm. The turbine is fitted on to the same input shaft as a...

Q:

Draw and calculate the two following gear trains. a.) Constraints: Input gear = 16 teeth; no two gears connected together can have a ratio of more than 6:1 ; Input gear = 10 rad/sec Make a simple...

Q:

Construct appropriate tables for each of the E-R diagrams in Exercises 2.2 to 2.4.

Q:

Think about your work history or even places where those you know have worked. What was that work environment like in each place? What did you like at each of those places? What was not so pleasing?...

Q:

If Emily Carey requested an accounting disclosure from General Hospital for the first time, what charge could the General Hospital assess her for this accountiy?

Q:

All corporations are required to issue Common Stock O Preferred Stock Bonds Oboth Common Stock and Preferred Stock