Question: Q 2 : Construct the conjugate beam with the loading and determine the slope at B . Knowing that A y = B y =

Q2: Construct the conjugate beam with the loading and determine the slope at B. Knowing that Ay=By=5kN.(25 mark)
VB=?
Please show all work
Q 2 : Construct the conjugate beam with the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Problem 3 ( 2 0 points ) . For the given beam with constant EI , answer the questions using Conjugate Beam Method: ( a ) [ 1 0 points ] Construct the conjugate beam for the given structure and...

Q:

Part 1 The solid 3 4 mm diameter shaft is used to transmit the torques applied to the pulleys. The shaft is supported in bearings at B and E . Determine the magnitude and direction of the torque T D...

Q:

The W14 X 43 simply supported beam is made of A-36 steel and is subjected to the loading shown. Determine the slope at A and B. A 10 ft C 2 kip/ft 10 ft B- 40 kip-ft

Q:

The W14 \(\times 43\) simply supported beam is made of A-36 steel and is subjected to the loading shown. Determine the slope at \(A\) and \(B\). 2 kip/ft 10 ft C 10 ft B 40 kip-ft

Q:

The W14 \(\times 30\) cantilever beam is made of A-36 steel and is subjected to the loading shown. Determine the slope and displacement at its end \(B\). 2 kip/ft A 6 ft 6 ft. B 30 kip-ft

Q:

Can you please help me solve these 10 Econ questions? I also attached the chapter just in case. Thanks so much!! :) MARKETS AND HOW THEY WORK 177 9.0 CHAPTER 9 LEARNING GOALS After reading this...

Q:

PLEASE COMPLETE NO LATER THAN 10/07 @8:00AM Each question(1,2,& 3) must be a minimum of 200 words. Please make answers detailed and knowledgeable based off the attached reading. ARE YOU ABLE TO...

Q:

Note - Use Conjugate beam method. Thanks Please solve these Deflections problems using A. Conjugate beam method 2. Determine the slope at point of the beam in the figure. E = 200 GPa, I = 6(106) mm....

Q:

Determine the slope and the displacement at midspan of the non-prismatic beam as shown in figure below. E = 200 GPa, I = 100 x 106 mm4. Use conjugate beam method. Use a) DIM b) MAM (deflection only)...

Q:

A solid cylindrical shaft with a diameter of 5 0 mm is subjected to a combined loading of a bending moment of 6 0 0 Nm and a torque of 5 0 0 Nm . Determine the principal stresses and the maximum...

Q:

Explain how the federal income tax structure affects the choice of financing (use of debt versus equity) of U.S. business firms.

Q:

Tyndol Fabricators Inc. manufactures a product in two departments. The product is cut out of sheet metal and bent to shape in the Cutting and Forming Department and then transferred to the Assembling...

Q:

ereveray wew Mitsui Electronics, Limited, is considering buying a labor - saving pierce of equipment and provided the following data: Purchase cost of the equipeent Anmual cost savings that will be $...

Q:

16 Part 1 of 2 0.64 points Required information [The following information applies to the questions displayed below.] Pro-Weave manufactures stadium blankets by passing the products through a weaving...