Question: Q . 7 Determine the structure stiffness matrix K for the frame and the support reaction at the fixed support 1 and 3 . Assume

Q.7 Determine the structure stiffness matrix K for the frame and the support reaction at the fixed support 1 and 3. Assume 1 and 3 are fixed. Take E=200GPa,I=300(106)mm4A=10(103)mm2 for each member.
Q . 7 Determine the structure stiffness matrix K

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Determine the structure stiffness matrix K for the frame. Take E = 2 9 ( 1 0 3 ) k s i , I = 6 0 0 i n 4 , A = 1 7 i n 2 for each member. Assume joints ( 1 ) and ( 3 ) are pinned; joint ( 2 ) is...

Q:

The two - member truss and degrees of freedom ( DOFs ) for each member are shown in the figure. Take EA as constant. The two - member truss and degrees of freedom ( DOFs ) for each member are shown...

Q:

Looking for worked solutions to part 2, 3 and 4. Answers are attached Q. 1 The frame structure ABCDE shown in Figure Q. 1 represents an idealised crane geometry and is fully fixed at A and E and has...

Q:

Q 1 [ k ] = E I [ 2 . 3 3 3 0 . 6 6 6 0 . 6 6 6 3 . 3 3 3 ] ii ) [ P ] = [ + 2 6 . 6 7 + 5 4 . 1 7 ] iii ) , 1 = 7 . 2 0 3 1 0 - 4 rads = B ; 2 = 1 4 . 8 1 3 4 1 0 - 4 rads = C ; iv ) M C B = 3 7 . 8...

Q:

Use the stiffness method to determine the following: - Stiffness matrix for each member - Global stiffness for the entire structure 15-1. Determine the moments at D and 3. Assume 2 is a roller and...

Q:

PLEASE COMPLETE NO LATER THAN 10/07 @8:00AM Each question(1,2,& 3) must be a minimum of 200 words. Please make answers detailed and knowledgeable based off the attached reading. ARE YOU ABLE TO...

Q:

Consider the beam structure shown in Figure 2. The figures below show the side view and front view of a steel cantilever beam structure (not to scale). The beam has three different cross-sections....

Q:

A 2 - story structure, which has 1 2 m x 8 m dimensions in plan, will be constructed. The typical plan view and the front view of this building is as given in Figures a and b , respectively. The...

Q:

Show a reasonable comprehension of conservative application improvement and use of direction programming instruments and progress conditions considering a prerequisites report. 2. Make sense of...

Q:

1. Show a reasonable comprehension of conservative application improvement and use of direction programming instruments and progress conditions considering a prerequisites report. 2. Make sense of...

Q:

Write the general solution of the following Bessel equation x'y'+xy'+(x - 4)y= 0 . GJ,(x)+c,Y,(x) b. GJ,(x)+c,Y,(x) Oc. GJ,(x) +c,J_(x) O d. GJ,(x) +C,J_(x)

Q:

Tamar Company manufactures a single product in two departments: Forming and Assembly. Information for the Forming process for May follows. Units Direct Materials Conversion Percent Complete Percent...

Q:

The payback period is generally viewed as a flawed capial budgeting technique, because it does not explicidy consider the time value of money by descounting cash flows to find presers valut. Irue...

Q:

Sandhill Remanufacturing rebuilds spot welders for manufacturers. The following budgeted cost data for 2022 are available for Sandhill: Time Charges Material Loading Charges Technicians' wages and...