Question: Draw the output waveform for the comparator circuit in figure below. Assume that +Vout(max) = +10 V and Vout (max) = -10V. Vin U1

Draw the output waveform for the comparator circuit in figure below. Assume

Draw the output waveform for the comparator circuit in figure below. Assume that +Vout(max) = +10 V and Vout (max) = -10V. Vin U1 Vout R1 +3 V 80ko R2 20ko

Step by Step Solution

★★★★★

3.50 Rating (160 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Tuus... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Electrical Engineering Questions!

Your division is considering two investment projects, each of which requires an up-front expenditure of $24 million. You estimate that the cost of capital is 9% and that the investments will produce...

Sketch the output waveform for the circuit of Fig. 13.40. +12 V 741 -12 V FIG. 13.40 Problem 2

Sketch the output waveform for the circuit of Fig. 13.42. +12 V t kn 339 5 V rms FIG. 13.42 Problem 6

Draw the resulting output waveform for the circuit of Fig. 13.41. +5 V V. FIG. 13.41 Problem 4

Refer to the counter circuit in Figure 5-48. Assume that all asynchronous inputs are connected to VCC. When tested, the circuit waveforms appear as shown in Figure 5-101. Consider the following list...

Show how to connect BCD-to-7-segment decoder/drivers and LED 7-segment displays to the counter circuit of Figure 7-22. Assume that each segment is to operate at approximately 10 mA at 2.5 V. Figure...

Describe the output waveform of each circuit in Figure 2050. Assume that the R L C time constant is much greater than the period of the input signal. +4 V -4 V (a) t FIGURE 20-50 C Vout www RL +15 V...

Refer to the logic circuit of Figure 4-41. Recall that output Y is supposed to be HIGH for either of the following conditions: 1. A = 1, B = 0, regardless of C 2. A = 0, B = 1, C = 1 When testing the...

Refer to the circuit of Figure 5-102. Assume that the ICs are of the TTL logic family. The Q waveform was obtained when the circuit was tested with the input signals shown and with the switch in the...

Repeat Problem 7.70 for the common-base circuit in Figure P7.71. Assume $V_{E B}($ on $)=0.7$ for the pnp transistor. The remaining transistor parameters are the same as given in Problem 7.70....

You learned in problem 6 (on the liquidity trap) in Chapter 5 that money demand becomes very flat at low interest rates. For this problem, consider the money demand function to be horizontal at a...

Consider two Italian restaurants located in identical towns 200 miles apart. The restaurants are identical in every respect but their tipping policies. At one, there is a flat $15 service charge, but...

This exercise studies the price competition between two major telcos in Australia: Telstra and Optus, and their relationship with NBN (National Broadband Network). NBN is a publicly-owned,...

[ 1 5 ] Evaluate the surface integral S F * d S , where F = - - y j k and S is given by the equation r ( u , v ) = ( : u 2 - 2 v , u v , u v 2 : ) , 0 u 1 , 1 v 4 .

Multicollinearity exists when the dependent variable and the independent variable are highly correlated. Do you agree? Explain.

What are the four key assumptions examined in specification analysis in the case of simple regression?

When using the high-low method, should you base the high and low observations on the dependent variable or on the cost driver?

The following data were extracted from the income statement of Brecca Systems Inc.: a. Determine for each year (1) the inventory turnover and (2) the number of days?? sales in inventory. Round to...

Describe the account analysis method for estimating a cost function?

5).-Un paquete de 2.00 kg se suelta en una pendiente de 53.1 a cuatro metros de distancia del resorte cuya constante de fuerza es de K = 120N / m y est sujeto a la basa de la pendiente, los...

Appendix G: (Not required information but I put it here incase it might help) b. Build a Simulink program based on the transfer function in Eq. (2-8) with R= 10k12 and C = 10uF. to conduct...

Design the circuit in Multisim. (figure 2). Should look similar to the Multisim diagram provided. Design a 5 volt DC output switching regulator with 10 volts DC of input. Pick the ratio for R1 and R2...

Use NI Multsim simulations to verify your calculations in: (1) Part (a). (2) Part (0) (3) Part (d). (4) Part (e). (5) Part (f). An analogue amplifier circuit is shown in Figure 1 below. VDD 15V Q3 04...

Critically and thoroughly analyse the circuit. Provide a thorough analysis with equations and diagrams. conclude based on the analysis whether you would recommend the circuit or not. The 32VRMs...

Use Cadence CIS Lite to draw the ideal inverting amplifier shown in Figure 10. R1 w Vin 1k U1 R2 ww 10k OPAMP OUD 0 Figure 10. Inverting op amp. Vout Using the part called 'VDC' found in 'SOURCE'...

Based on the information in Table 5.1, estimate a. The weight of a laptop computer. b. The propulsion force of a bicycle. Table 5.1 TABLE 5.1 Approximate magnitude of some typical forces Force...