Question: Question Time Remaining 40 02:57:00 How should sheathing fasteners be driven in relation to the surface of the sheathing? 1. With the crown breaking the

Question Time Remaining 40 02:57:00 How should

Question Time Remaining 40 02:57:00 How should sheathing fasteners be driven in relation to the surface of the sheathing? 1. With the crown breaking the surface of the sheathing 2. 3. 4. With the head embedded up to 1/8" below the surface of the sheathing With the base of the head snug against the surface of the sheathing With the crown flush with the surface of the sheathing Question Answered 0 Question 39 A shaft enclosure shall have what fire rating when connecting six stories? 1. 2. 3. 4. 1 hr 2 hr 3 hr Time Remaining 02:57:04 4 hr Question Answered 0 Question 38 What is the web depth of a cold-formed steel framing member with the designation 800S162-54? 1. 2. 3. 4. 1-1/4 inches 1-5/8 inches 8 inches Time Remaining 02:57:07 16-1/8 inches Question Answered 0 Question 37 Cement is a mixture of which basic materials? 1. Water, aggregates, and cement 2. 3. 4. Sand, water, and crushed rock Soil, water and cement Water, volcanic ash, and soil Time Remaining 02:57:14 Question Answered 0 Question Time Remaining 02:57:17 36 How many pieces of 1" x 4 x 8' reflective insulation will be needed to insulate a 32 x 64' roof? 1. 52 2. 56 3. 60 4. 64 Question Answered 0 Question Time Remaining 35 02:57:25 What is the MINIMUM thickness of fiber cement panel siding applied as a weather covering? 1. 2. 3. 4. 1/4 in. 3/8 in. 1/2 in. 5/8 in. Question Answered 0 Question Time Remaining 34 02:57:28 What is the MINIMUM lap at the joints for 6 mil polyethylene installed as dampproofing under a slab? 1. 2. 3. 4. 4 in. 6 in. 8 in. 10 in. Question Answered 0 Question 33 Concrete used in slipforming must have a very low: 1. set-time. 2. water-ratio. 3. slump. 4. weight. Time Remaining 02:57:31 Question Answered 0 Question 32 Which power transmission thread is strongest? 1. Crenellated 2. Buttress 3. Square 4. Acme Time Remaining 02:57:34 Question Answered 0 Question 31 Question Answered 0 How much do two pieces of rebar weigh if the bar is 1/2 inch in diameter, 20 feet long, and the steel used weighs 500 lbs/cu. ft.? 1. 2. 3. 4. 34.75 lbs 27.80 lbs 13.90 lbs Time Remaining 02:57:37 6.95 lbs

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Question 37 Cement is a mixture of which basic materials? 1. Water, aggregates, and cement 2. 3. 4. Sand, water, and crushed rock Soil, water and cement Water, volcanic ash, and soil Time Remaining...

Question 70 Which of the following is used to minimize concrete cracking? 1. Edging 2. Joints 3. Additional aggregate 4. Rebar Time Remaining 02:54:40 20502 Wall thickness. (inches) 6 8 12 Volume of...

Question Time Remaining 61 02:55:15 What is the MINIMUM fire-resistance rating for the structural frame supporting only the roof of a Type I B building? 1. 2. 3. 4. O hour 1 hour 2 hour Question...

Question Time Remaining 02:56:30 50 Which of the following criteria can be used by itself to determine if soil is expansive? 1. More than ten percent of soil particles pass a No. 200 sieve. 2. 3. 4....

Whittier Photograchy's checkbook lints the following Click the icon to view the checkbook) Whittier's November bank statement shows the following: (Click the icon to view the November bank statement)...

Skip to main content EXAM # 3 AnswerSaved Help opens in a new windowSave & ExitSubmit Item 3 3 2 points Time Remaining 4 0 minutes 1 2 seconds 0 0 : 4 0 : 1 2 References Item 3 3 Time Remaining 4 0...

Question Time Remaining 02:58:37 17 For what MINIMUM time after depositing must concrete be protected from freezing? 28 days 1. 2. 3. 4. 14 days 7 days 5 days Question Answered 0 Question Time...

Question 20 What should be done before beams are hung? The columns should be set in place 1. 2. 3. 4. The joists should be installed The girders should be loosely installed The structure should be...

Question 30 Where is the means of egress illumination level measured? 1. 2. 3. 4. At handrail height At the fixture At eye level At the walking surface Time Remaining 02:57:40 Question Answered 0...

The coordinates of the endpoints of GH are G(2, 7) and H(11, 16). Point I is on GH and divides it such that GI:HI is 4:5. What are the coordinates of I? Write your answers as integers or decimals.

Bob, Carol, and Ted are residents of a tiny commune in darkest Peru. Bob currently has a utility level (Ub) of 55 utils, Carol's utility (Uc) is 35 utils, and Ted's utility (Ut) is 10 utils. Alice,...

The circumference of a circular disc is 39 cm. Work out the diameter of the disc. Give your answer correct to the nearest millimetre. For questions, use the button on your calculator.

As the manager of Smith Construction, you need to make a decision on the number of homes to build in a new residential area where you are the only builder. Unfortunately, you must build the homes...