Question: Rigid member ABC is subjected to a vertical load P at point A as shown. Member CD is a uniform rectangular bar (15mm x

Rigid member ABC is subjected to a vertical load P at point

Rigid member ABC is subjected to a vertical load P at point A as shown. Member CD is a uniform rectangular bar (15mm x 5 mm) of steel (E = 200 GPa) pinned at ends C & D. A 6 mm diameter pin is used at point C and a 4 mm diameter pin at point D. The allowable shear stress at pins C and D is 250 MPa and the allowable normal stress in member CD is 175 MPa. Determine the maximum load P that can be applied. Also, for this maximum load P what is the vertical displacement of point A? P A B C C -6 mm t-5 mm 2N w=15 mm t=5 mm LAB=250 mm Lac=150 mm BC L=200 mm CD t= 5mm 4 mm D

Step by Step Solution

★★★★★

3.49 Rating (152 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Programming Questions!

Golden Food Products produces special-formula pet food. The company carries no inventories. The master budget calls for the company to manufacture and sell 123,000 cases at a budgeted price of $60...

Question 6 Lower of Cost or Market Method: Target currently has the following products, as listed below: Original Cost Market Price Inventory per unit Quantity per unit A $90 $150 200 B $530 $325 50...

5. Write an algorithm to program a robot to pick up two blocks (the blocks are of different sizes) from fixed positions on either side of a center position and to stack the blocks in the center...

1. What is Richard's full retirement age (FRA)? (10 points) 2. What is the reduced monthly SS retirement benefit if Richard draws at age 62? Show your calculation. (15 points) 3. What is the...

A downward load of Q = 3 6 kN is app ` lied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 2 5 kN at joint E plus a force at joint D from the rigid...

The frame is used to support a 3 - in . - thick plywood floor of a residential dwelling shown in ( Figure 1 ) . Set a = 5 ft , b = 9 ft . Figure 1 of 1 A rectangular steel framework consists of a set...

HW 0 1 MEMT 2 1 2 Last Revised 9 / 4 / 2 4 ( adapted from Hibbeler 1 0 t h ed . probs. 4 - 3 1 & 4 - 3 2 ) Eight A 9 9 2 steel, 1 inch diameter, reinforcing rods are embedded into high strength...

Describe the difference between the value of x in a binomial distribution and in a geometric distribution. Question content area bottom Part 1 Choose the correct answer below. A. In a binomial...

A simple truss shown in Figure 1 consists of four identical members ( A B , B C , C D , and DB ) . All A rigid beam BCD , shown in Figure 2 , is supported by a pin at C and 2 identical cables (...

The salvage value S (in dollars) of a company yacht after t years is estimated to be given by the formula below. Use the formula to answer the questions. S(t) = 600,000(0.7) What is the rate of...

Suppose you are a manager of Fitters Accounting and Finance department. What human resources information do you think you would need to effectively manage your Accounting and Finance employees?

The following related discrete problem also gives a good clue for the answer to Exercise 32. Randomly select with replacement t1, t2, . . . , tr from the set (1/n, 2/n, . . . , n/n). Let X be the...

5.77 Solve Prob. 5.48 using PSpice or MultiSim and op amp LM324.

Consider the following data sample data obtained in a study of relationship between the number of that applicants for a certain foreign service jobs have studied German in high school or college and...

Horizons Inc. has agreed to sell an investment in a subsidiary that has been accounted for on the equity method of accounting to a minority stockholder in exchange for the stockholders share in...

Consider the three linearly separable two-dimensional input vectors in the following figure. Find the linear SVM that optimally separates the classes by maximizing the margin. + +

Consider a binomial experiment with n = 8 and p = 0.2. a. Compute f(0) (to 4 decimals). b. Compute f(6) (to 4 decimals). c. Compute P(x<=4) (to 4 decimals). d. Compute P(x>=3) (to 4 decimals)....

A shipment of 250 net books contains 3 defective units. Determine how many ways a vending company can buy three of these units and receive: A) No defective units b) All defective units c) At least...

Property taxes levied for the current year but not collected until after 60 days in the next fiscal year are:Select one:a. Deferred outflows of resourcesb. Near-term liabilitiesc. Financial assetsd....

Gildan Activewear Inc. is principally in the business of manufacturing and selling activewear, socks, and underwear. Exhibits 9-9A and B contain the statements of financial position and statements of...

Note 13 to the January 25, 2014, financial statements of Le ChÃ¢teau Inc. is shown in Exhibit 11-9. All dollar amounts are in thousands. Required: a. Describe the differences between the...

Explain the basic differences between periodic and perpetual inventory systems.

Repeat Problem 11, skipping part (e), but use LN_BLDTL as the dependent variable. Problem 11 a. Conduct a one-way ANOVA, with dosage level (PPM_TOLU) as a categorical predictor. b. Using the...

Use the data from Freund (1979), presented in Problem 22 in Chapter 14. Taking the model discussed there as the maximum model, repeat parts (a) through (h) of Problem 6. In part (h), note the...

For the data given in Problem 4 in Chapter 8 (plus the accompanying computer output), find (using = .10) the best regression model relating homicide rate (Y) to population size (X1), percentage of...