Question: shear stress in a solid shaft is not to exceed 40N/mm. When the torque transmitted to 20,000 Nm. Determine is the maximum diameter of

shear stress in a solid shaft is not to exceed 40N/mm. When

shear stress in a solid shaft is not to exceed 40N/mm. When the torque transmitted to 20,000 Nm. Determine is the maximum diameter of the shaft. Give your answer in mm to no nearest whole number.

Step by Step Solution

★★★★★

3.50 Rating (170 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The detailed ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

A solid shaft is subjected to an alternating torque varying from -200 N-m to +300 N-m. The shaft is ground and reliability is 90%. Calculate shaft diameter for infinite life. Take factor of safety of...

Find the maximum shear stress in a 10-in circular saw if it runs idle at 7200 rev/min. The saw is 14 gauge (0.0747 in) and is used on a -in arbor. The thickness is uniform. What is the maximum...

Find the maximum shear stress in a 5 -in-diameter circular saw blade if it runs idle at 5000 rev/min. The saw is 14 gauge (0.0747 in) steel and is used on a 5/8-in-diameter arbor. The thickness is...

Write a program to ask the user to enter number less than 5 5 using the below code as a skeloton. If the user enters greater than 5 , 5 , the program will loop to ask the user to enter the number...

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Part 1 The solid 3 4 mm diameter shaft is used to transmit the torques applied to the pulleys. The shaft is supported in bearings at B and E . Determine the magnitude and direction of the torque T D...

Research shows that delinquent behaviors (e.g. stealing, skipping school) increase between early- to mid-adolescence (approximately age 12 to 16). Research has also shown that this increase is...

ASSETS B C D E G CURRENT LIABILITIES CURRENT ASSETS. 2019 2018 Accounts payable $737,144 $593,171 Cash and cash Accrued expenses and other $58,211 $46,938 331,738 318,204 equivalents current...

The diagram shows a three-component SOW phase diagram depicted at a constant temperature (T), and pressure (P). Consider the composition marked by the red arrow as point Y. In light of the Phase...

Small Country Export Subsidy, we discussed the welfare implications of export subsidy and production subsidy for a small country. We will look at this problem in more detail here. Consider the...

A lease option is a clouse that grants an option holder the right, but not the obligation, to renew the lease, cancel the agreement, relocate whin a property, or even expand to adjacent space. The...

A). Describe the shape and level of the current Yield Curve in Australian Commonwealth Government Securities (i.e., at the time you decide to answer this question use data gathered from Eikon and...

The rocket moves in a vertical plane and is being propelled by a thrust T of 32 kN. It is also subjected to an atmospheric resistance R of 9.6 kN. If the rocket has a velocity of 3 km/s and if the...

Go to the website of DBRS at dbrs.com. Use Quick Search and Ticker Lookup to find Manufacturers Life Insurance Company and look up its rating. Do the same for Loblaw Companies Limited and Rogers...

The profits after tax of D plc are as follows: Year to 30 September 2016............... 50,000 Year to 30 September 2017............... 52,800 On 1 October 2015, the company's issued share capital...

Using the standardized regression equation of zy = rz x , find the predicted dependent variable z-scores of individuals with the following individuals if r = 0.72: a. z x = 4.0 b. z x = 2.9 c. z x =...

The Mahalanobis distance procedure is important for identifying what potentially problematic data issue? A. Kurtosis B. Missing data C. Influential multivariate outliers and observations responsible...

Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case. 30 ksi 9 ksi

The industrial robot is held in the stationary position shown. Draw the shear and moment diagrams of the arm ABC if it is pin connected at A and connected to a hydraulic cylinder (twoforce member)...

The bar has a cross-sectional area of 400(10 6 ) m 2 . If it is subjected to a uniform axial distributed loading along its length and to two concentrated loads, determine the average normal stress in...

The time needed for performing a machining operation is to be investigated. Historically, the process has had a standard deviation equal to .146 minute. The means (in minutes) of 39 samples of n = 6...

Visit http://www.qualitymag.com, find the case study from the current issue (under Departments on tire lower right side) and summarize it.

Design specification for a motor housing states that it should weigh between 24 and 25 kgs. The process that produces the housing yields a mean of 24.5 kg and a standard deviation of .2 kg. The...