Question: Shrinkage allowance on pattern is provided to compensate for shrinkage when the Metal changes from liquid state to solid state at freezing temperature Solid phase

Shrinkage allowance on pattern is provided to compensate for shrinkage when the
Metal changes from liquid state to solid state at freezing temperature
Solid phase temperature drops from freezing temperature to the room temperature
Liquid metal temperature drops from pouring temperature to room temperature
Liquid metal temperature drops from pouring temperature to freezing temperature

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

Required information Comprehensive Problem 07-63 (LO 07-1, LO 07-2, LO 07-3, LO 07-4) (Algo) [The following information applies to the questions displayed below] During 2021, your clients, Mr. and...

Q:

LABORATORY 1: HEAT TRANSFER AND PHASE CHANGES Objectives: 0 to predict how energy will ow when objects are heated or cooled, or for objects in contact that have different temperatures a to explain...

Q:

1. 20.00 1882 3. CHEM 1P92 Assignment 12A (Solutions). Version 8 179 Fill in the blanks in the table for aqueous solutions of the compounds shown. The density of the solution is in g/ml.....

Q:

Hi dear Tutor please help me with these questions. please answer all. Thank you in advance cricau shuth Columbia broke' or Fexas while returning from a in space on Fichruan' 1.2003. of the seren...

Q:

Space Shuttle Challenger Mission 51-L Launch Decision On January 28,1986 , the Space Shuttle Challenger was launched for the last time. The decision to launch the Challenger was not simple. Certainly...

Q:

effective status reports used in project management. b) Discuss challenges and pitfalls for each of the projectstatus reports. c) Explain the difference between the projectstatusreports provided for...

Q:

please help me with this section Phase Changes Each inclividual chemical (Whilie in its llquid state) has what is called a freering and a boiling point. The boling point of a llquid is when the...

Q:

Chapter 7: Wastewater Management IN THIS CHAPTER U.S. wastewater regulations Sources of contamination of wastewaters Classification of water pollutants Characteristics of wastewater Wastewater...

Q:

Chapter 5: Hazardous Waste Site Clean-Up Technologies IN THIS CHAPTER Treatment technologies for contaminated hazardous waste sites Containment technologies for contaminated sites Innovative...

Q:

Chapter 5: Hazardous Waste Site Clean-Up Technologies IN THIS CHAPTER Treatment technologies for contaminated hazardous waste sites Containment technologies for contaminated sites Innovative...

Q:

A mixture of 4 kg of water vapor and 96 kg of dry air exists at 100 kPa and 25 8C in a 10-m3 volume. Determine the molar mass of the mixture and the volume occupied by the vapor. This represents very...

Q:

Write the structure of the expected product from the reaction of 1-chloro-2, 4-dinitrobenzene with each of the following reagents: (a) CH3CH2ONa (b) C6H5CH2SNa (c) NH3 (d) CH3NH2

Q:

When comparing the interest rate on credit card debt to the interest rate on a mortgage, which of the following is the most accurate? The interest rate on the credit card debt is higher because the...

Q:

Homework: Chapter 14 Homework Question 1, P14-2 (similar to) Part 1 of 2 (Defining capital structure weights) In August 2015 the capital structure of the Emerson Electric Corporation (EMR) (measured...

Q:

5. Understand how cultural values influence conflict behavior.

Q:

6. Describe how communication can reinforce cultural beliefs and behavior.

Q:

3. Analyzing a Film. View a feature film or a video (e.g., Chir-raq or Brooklyn) and assume the position of a researcher. Analyze the cultural meanings in the film from each of the three...