Question: Suppose, switch S1 is connected to P1.1 and switch S2 is connected to P1.2. When S1 on and S2 off, an LED is switched on.

Suppose, switch S1 is connected to P1.1 and switch S2 is connected to P1.2. When S1 on and S2 off, an LED is switched on. If S1 off and S2 on, your intake and roll will be displayed in an LCD. And in both cases, a 7 segment display will show the value of switch that is on(7 segment will show 1 if S1 is on, 2 if S2 is on; and 0 if both switch are off) Implement this design using 8051 in proteus and code in keil.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

In this mini-case, you will complete the test of details on accounts receivable for the 2019 audit of EarthWear Clothiers, Inc. The principal test of detail involves sending "confirmations" or...

Do the following: 1. Suppose, switch S1 is connected to P1.1 and switch S2 is connected to P1.2. When S1 on and S2 off, an LED is switched on. If S1 off and S2 on, 40 and 32 will be displayed in an...

Suppose that three switches are used to connect 10 hosts (h_0, h_1, ..., h_9). Assume switch s_1 is connected to h_0,h_1,h_2,h_3, and switch s_2 (using interfaces 1 to 5 respectively); s_2 is...

Below is code used to increment and decrement an LED counter using a switch (S1) on the MSP432 P1.1 to increment; and (S2) externally connected to P5.0 and P5.2 to decrement the led. However, when...

Suppose that three switches are used to connect 10 hosts (h_0, h_1, ..., h_9). Assume switch s_1 is connected to h_0, h_1, h_2, h_3 and switch s_2 (using interfaces 1 to 5 respectively); s_2 is...

OL-39 CAPACITORS IN CIRCUITS ONLINE LAB 7/1/2020 OBJECTIVES The purpose of this lab will be to determine how capacitors behave in R-C circuits by measuring the time for charging and discharging. The...

-Use CCS -MSP432 microcontroller Write an assembly program to control the Red, Green, Blue LEDs on the evaluation board according to the statuses of the two switches S1 and S2. Press only S1: RED...

Objectives: This lab introduces the MSP432 board and booster pack from Ti and the energia software tool. This lab also gives you hands-on experience to use the push buttons and the RGB LED....

Make a lab from this lecture Inter-VLAN Routing Now you know how to segment and organize your network into VLANs. Hosts can communicate with other hosts in the same VLAN, and you no longer have hosts...

answer all yes its an assignment You have two switches S1 and S2 directly connected. VLAN 2 is assigned to ports 1 through 4 of each switch. VLAN 3 has been assigned to ports 8 through 11 of each...

Why must Work in Process Inventory be adjusted for factory overhead applied at year-end?

Tyler owned a non-residential building, purchased in 2019, the original cost of which was $500,000, plus $250,000 for the cost of land. The UCC value of the building was $390,000, and the land and...

Question 6 1 . 8 Points Question 6 What is Future Value of money?

4. A new procedure for the determination of sulfur in coal was tested on a standard coal sample with a certified value of 2.14% sulfur by mass. The new procedure gave results of 2.11%.2.07%.2.04%....

Provide examples of KPIs in Human Capital Management.

What would an Internal Compa-Ratio of 118% indicate for an employee?

What are OLAP Cubes?