Question: The 4 - mm - diameter cable B C is made of a steel with E = 2 0 0 GPa. Knowing that the maximum

The 4-mm-diameter cable BC is made of a steel with E=200 GPa. Knowing that the maximum stress in the cable must not exceed 190
MPa and that the elongation of the cable must not exceed 5 mm , find the maximum load P that can be applied as shown.
The maximum load P that can be applied is
alephkN.
The 4 - mm - diameter cable B C is made of a

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Question 4: A steel disc of 750 mm outer diameter is shrunk onto a steel hub of 80 mm diameter. The interference on the diameter is 0.05 mm. (a) Find the maximum hoop stress in the disc at...

Q:

A 250 N load is applied vertically to a pipe wrench which is gripping to a pipe assembly as shown in Figure Q1(a). The pipe assembly is made of stainless steel (E-193 GPa, yield.at - 207 MPa), with...

Q:

The design specifications of a 1.2-m-long solid circular transmission shaft require that the angle of twist of the shaft not exceed 4 when a torque of 810 N-m is applied. Determine the required...

Q:

1. Determine reasonable design values for the number of active coils, the wire and coil diameters of an infinite-life helical compression spring with a minimum load of 12 lb force and a maximum load...

Q:

6. Consider a bike crank FEA simulation as shown in Figure 8, where we apply a load (F) of 500 N at the pedal end and a full constrain at the shaft end as shown in the figure below. The crank is made...

Q:

The shaft is made of A992 steel with the allowable shear stress of Ï allow = 75 MPa. If gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively,...

Q:

A solid cylindrical shaft is subjected to a bending moment of 4 0 0 Nm and a torque of 2 5 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft is subjected to a bending moment of 5 0 0 Nm and a torque of 3 0 0 Nm . Determine the principal stresses and the maximum shear stress at a point on the surface of the shaft....

Q:

A solid cylindrical shaft with a diameter of 5 0 mm is subjected to a combined loading of a bending moment of 6 0 0 Nm and a torque of 5 0 0 Nm . Determine the principal stresses and the maximum...

Q:

On January 1, 2021, ACME Corporation purchased a machine for $11,000 on account. The company uses straight-line depreciation and estimates that the machine will have a eight-year useful life. The...

Q:

Hayes Industries purchased the following assets and constructed a building as well. All this was done during the current year. Assets 1 and 2: These assets were purchased as a lump sum for $100,000...

Q:

When preparing a tax return for a short period, the taxpayer should annualize the income if the short period return Option A is the last return for a decedent who died on June 1 5 . Option B is the...

Q:

explain in detail a home based business, pros and cons ofstarting a home based business? give examples 2 answers