This problem relates to tolerance stack-up using the absolute tolerance system, as explained in section 1-14....
Fantastic news! We've Found the answer you've been seeking!
Question:
Transcribed Image Text:
This problem relates to tolerance stack-up using the absolute tolerance system, as explained in section 1-14. In the figure below, specified dimensions are as follows (all units in inches): b 1.7550.002 2.015±0.004 A b B d 3.200 0.007 ?+0.010 D c C (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what is the correct nominal dimension for d? (b) Under the assumptions of the preceding question, what would be the most likely value for the gap, w? Would it be 0.015 in? This problem relates to tolerance stack-up using the absolute tolerance system, as explained in section 1-14. In the figure below, specified dimensions are as follows (all units in inches): b 1.7550.002 2.015±0.004 A b B d 3.200 0.007 ?+0.010 D c C (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what is the correct nominal dimension for d? (b) Under the assumptions of the preceding question, what would be the most likely value for the gap, w? Would it be 0.015 in?
Expert Answer:
Related Book For
Posted Date:
Students also viewed these finance questions
-
Was the Russian Revolution a success? Why or why not? What were the goals of the revolution and were they achieved? Should Russia celebrate/commemorate the 100 year anniversary of the Revolution? Are...
-
In your post with your file attachment respond to the following questions What challenges have you faced while completing your introduction and conclusion Which part s of your introduction and...
-
Respond to the following questions in at least one paragraph each. reference cited needed 1. What is the definition of planning? Of strategic planning? Of operational planning? 2 . What is the value...
-
Identify and discuss three ways that tourism and hospitality businesses can maintain a long-term relationship with their clients
-
What major factors contribute to the increased complexity of media planning?
-
Classify the following items as issuance of stock (I), dividends (D), revenues (R), or expenses (E). Then indicate whether each item increases or decreases stockholders equity. (1) Rent Expense (2)...
-
The Wide World of Fluids article titled "Nanoscale Flows,". (a) Water flows in a tube that has a diameter of \(D=0.1 \mathrm{~m}\). Determine the Reynolds number if the average velocity is 10...
-
Perez County entered into a number of transactions for the current fiscal year. Identify the fund or funds affected by each transaction and determine how each transaction will affect the accounting...
-
Write a paper on one of the following topics: Describe the likely short-run and long-run economic consequences of EITHER (a) The COVID-19 pandemic and the associated lockdowns OR (b) Climate change....
-
Find each function f(x) given, (a) find any three ordered pair solutions (a,b), then (b) algebraically compute f(x), and (c) verify the ordered pairs (a,b) satisfy f(x). f(x)=x-2 f(x)=x +3 f(x) = x +...
-
Baseball Magazine, a domestic corporation, markets pictures of baseball players on its website. Its database server is in the Cayman Islands. Baseball fans access the Web page and use their credit...
-
Hiring decisions are more complex today than ever before. Not only is the cost to hire an employee expensive, but so is the cost of training and development. Discuss.
-
Define Job Evaluation. List and summarize the six steps in Job Evaluation process.
-
4. For = {a, b}, construct dfa that accept the set consisting of all strings with at least two a's. (points: 3) 5. For = {a, b), construct dfa that accept the set consisting of all strings with at...
-
What is the legal basis for protecting employees from harassment with supporting laws or regulations explain in detail.
-
Robert is inspecting a shipment of 22 inch pipes. The lengths of the pipes may vary by 1%. What is the range of allowable lengths in the pipes?
-
A. Conducting plates with constant charge density 1. How does the electric field at point 1 compare to that at points 2, 3, and 4? Explain. The field for 1,3 & 4 . elstance doesn't Ore all the Some...
-
Which property determines whether a control is available to the user during run time? a. Available b. Enabled c. Unavailable d. Disabled
-
What are the important considerations in determining a promotion budget?
-
What does Googles website (www.Google.com) tell us about the companys ability to collect information about individuals and businesses? What privacy issues arise, and how can they be resolved?
-
Review the McKinsey & Co. website. Are there indications that the consulting company is market-oriented?
-
The tube is subjected to a torque of 750 N. m. Determine the amount of this torque that is resisted by the gray shaded section. Solve the problem two ways: (a) by using the torsion formula, (b) by...
-
The solid shaft has a diameter of 0.75 in. If it is subjected to the torques shown, determine the maximum shear stress developed in regions BC and DE of the shaft. The bearings at A and F allow free...
-
The solid shaft has a diameter of 0.75 in. If it is subjected to the torques shown, determine the maximum shear stress developed in regions CD and EF of the shaft. The bearings at A and F allow free...
Study smarter with the SolutionInn App