Question: The bar A B has a pin support at C and is attached to a cable ( AD ) at A . The bar is

The bar AB has a pin support at C and is attached to a cable (AD) at A. The bar is subjected to a vertical load of 45N at B. Determine the tension in the cable AD knowing that a=406cm.
a. TAD=3654.00N
b. TAD =10048.50N
c. TAD=1370.25N
d. TAD=1937.31N
e. TAD=950.04N
Finish attempt
The bar A B has a pin support at C and is

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

The bar AB has a pin support at C and is attached to a cable (AD) at A. The bar is subjected to a vertical load of 33 N at B. Determine the tension in the cable AD knowing that a = A 10 cm to D a 12...

Q:

To analyze a beam subjected to a vertical force and a triangular distributed load, determine the reaction forces acting on each of the supports, determine the minimum pin diameter for one support...

Q:

A rigid beam ABC is supported at C by a pin support, and at A and B by timber struts AD and BE which are in turn supported by pin supports at D and E respectively (Figure 1). The struts AD and BE are...

Q:

The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its...

Q:

The assembly in Fig. P-242 consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm,...

Q:

The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A between the lower end of the left rod and its pin...

Q:

Rigid member ABC is subjected to a vertical load P at point A as shown. Member CD is a uniform rectangular bar (15mm x 5 mm) of steel (E = 200 GPa) pinned at ends C & D. A 6 mm diameter pin is used...

Q:

A cable and pulley system at D is used to bring a 230-kg pole (ACB) to a vertical position as shown in the figure part (a). The cable has tensile force T and is attached at C. The length L of the...

Q:

= The vertical bar is subjected to a uniformly distributed load (w 83 lb/ft) over the top 6 ft. It is supported by a pin support at A and a spring between B and D with a pin support at D. The spring...

Q:

2.94 The elastic strip with a cutout is of length L, width b, and thickness t. Derive the expression for the elongation of the strip caused by the axial load P. 2.95 The aluminum bar of...

Q:

22 (2 points) On June 30, 2020, Raemond exchanged his apartment complex worth $1,000, FMV for an office building worth $800,000 and $100,000 cash. Raemond boug property on September 20, 2015 for...

Q:

An exponential function f(x) = ab' passes through the points (0, 11000) and (3, 11). What are the values of a and b? a= b

Q:

Dave, Ella and Jia share their electricity bills in the ratio 3 : 4 : 5. a How much does each of them pay when their electricity bill is i $168 ii $192 iii $234? b Show how to check your answers to...

Q:

O False Welfare effects of a regional trading arrangement are not always static. There are also dynamic gains that influence growth rates over the long run and offset unfavorable static effects due...