Question: The beam shown is 1000 mm long with cross section of 50 mm by 100 mm, and is subjected to a load of 500

The beam shown is 1000 mm long with cross section of 50

The beam shown is 1000 mm long with cross section of 50 mm by 100 mm, and is subjected to a load of 500 kgs. A 7018 electrode is used to weld the beam section all around [as shown]. Weld size is 12 mm. Approximate the maximum stress in the weld. Compare the maximum weld stress with the strength of the electrode. 12 100. 1000 1 1 100

Step by Step Solution

★★★★★

3.46 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given Data Beams Length Length 1000mm Cross Sectio... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

CamCo Ltd. leased floor space in a new office building. Rent will cost $10,000 per month for a ten-year iease, but some renovations are needed and will be pald by CamCo to customize the space. The...

The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an angle of 25° with the horizontal as shown, determine the normal and shear stress that act...

The beam shown is loaded in the xy and xz planes. (a) Find the yz components of the reactions at the supports. (b) Plot the shear-force and bending-moment diagrams for the xy and xz planes. Label the...

Flow between two tanks (Fig. 7B.4). Case I: A fluid flows between two tanks A and B because PA > PB. The tanks are at the same elevation and there is no pump in the line. The connecting line has a...

A simply supported beam is loaded with a point load, as shown in the figure. The beam is a steel wide flange (W 12 X 35) in strong axis bending. Calculate the maximum deflection of the beam and the...

The top plate made of 2014-T6 aluminum is used to reinforce a Kevlar 49 plastic beam. If the allowable bending stress for the aluminum is ( allow ) al = 40 ksi and for the Kevlar ( allow ) K = 8...

If the beam is made of material having an allowable tensile and compressive stress of (sigma allow)t = 125 MPa and (sigma allow)c = 150 MPa, respectively, determine the maximum allowable internal...

4.What information is needed when determining the size of a structural member to use (say you are determining if it is appropriate to use a douglas fir or pine 2 x10 or 2 x 12 wood joist or perhaps a...

Determine the minimum width of a 30ft long cantilever W14 steel I-beam that carries a uniform 300 lb/ft load without exceeding a maximum allowable bending stress of 30 ksi. Then, check that the...

The picture shows the load and cross-section of the bridge girder. The material is S355. a) Where is the critical cross-section of the structure at the fracture limit. b) Where is the critical...

Danny Venable, the new controller of Seratelli Company, has reviewed the expected useful lives and salvage values of selected depreciable assets at the beginning of 2014. Here are his findings: All...

On January 1, 2021, Tennessee Harvester Corporation issued debenture bonds that pay interest semiannually on June 30 and December 31. Portions of the bond amortization schedule appear below: Increase...

your ideas about and experiences with Reacting to Change, Framing Change, and Managing Change three quotes or paraphrases from three outside sources ( one per section ) supporting your ideas about...

What percentage of volume of a rectangular block having specific gravity 0.8 is submersed inside the oil having specific gravity 0.9?

Find the extreme points of P. Let P = {x E R : Ax 0}, where 1 2 1 -3 3 A and b 1 4 -2

What is the rise of water in a glass capillary tube having a radius of 0.5 mm and surface tension of 0.1 N/m? Assume the contact angle of water and glass is 0 degrees.

A curved gate having 3 m wide is supporting the water as shown in Figure 1. Find out the magnitude of the resultant pressure force and its direction. 2 m 30 Curved Water Gate 2 m Figure 1

Determined the sensitivity of an inclined manometer having an angle of 30 degree between inclined column and vertical is equal to?

Solve Flounder Co. invested $920,000 in Culver Co. for 25% of its outstanding stock. Culver Co. pays out 30% of net income in dividends each year. Use the information in the following T-account for...

D1 Task 4 Determine the values of distribution of shear force and bending moment and locate a point of contra flexure for a simply supported beam with overhang carrying at least two concentrated...

Show all your work including VBA code and results of your computation in the spreadsheet as screen captures. Problem 1 Wr y = 1201(EI) A set of formulas to calculate the deflection (y) of a beam at a...

MATLAB CODE I need help understanding what (x) is in the question. I don't know how to relate x to the number of nodes N Consider the cantilever 1 beam shown in Fig. 1: Figure 1: Schematic of a...

Please solve this question with clear steps.And.Check the answers or make sure that they are right. Image transcription text 4 QUESTION 4 (40 Points) Using the finite element method, determine the...

ANSWER IN MATLAB CODE PLEASE 1. The beam below is supported by rollers on the left side and is fixed on the right side. There is a linear distributed load along the length of the beam shown in figure...

Section I Short Answer. 1 mark each. Answer in the boxes provided. Use space provided for rough work. 1. A 6.0 kg mass is pulled up a 20 m long, 15'3 ramp at a constant speed of225 m.-"'s. What power...