Question: A beam 1m long with dimensions b = 50 mm and d = 100 mm is subjected to a load of 500 kgs as

A beam 1m long with dimensions b = 50 mm and d

A beam 1m long with dimensions b = 50 mm and d = 100 mm is subjected to a load of 500 kgs as shown. A 7018 electrode is used to weld the beam section all around. Weld size is 12 mm. Approximate the maximum stress in the weld. Compare the maximum weld stress with the strength of the electrode. y F 12 V b -X d

Step by Step Solution

★★★★★

3.39 Rating (143 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Given step1 beam Im lon... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an angle of 25° with the horizontal as shown, determine the normal and shear stress that act...

The 1/2-in.-diameter bolt hook is subjected to the load of F = 150 lb. Determine the stress components at point B on the shank. Show the result on a volume element located at this point. 1.5 in. A 30...

A simple beam AB is subjected to a load in the form of a couple M0 acting at end B (see figure). Determine the angles of rotation Î¸A and Î¸B at the supports and the...

An AISI 1020 cold-drawn steel tube has an ID of 40 mm and an OD of 50 mm. What maximum internal pressure can this tube take if the largest principal normal stress is not to exceed 80 percent of the...

A compression bar having a square cross-section with sides b = 50 mm is subjected to load P. The bar is constructed from two pieces of wood that are connected by a glued joint along plane pq that is...

Solve the preceding problem for a box beam with dimensions h = 200 mm, h1 = 160 mm, b = 150 mm, and b1 = 130 mm. Assume that the beam is constructed of steel with yield stress Y = 220 MPa.

Solve the preceding problem for a box beam with dimensions h = 400 mm, h1 = 360 mm, b = 200 mm, and b1 = 160 mm, and with yield stress Y = 220 MPa.

Utilizing resoorces, complete a risk audit of Bank of Americas project to acquire Merrill Lynch. Ensure you address all 10 critical success factors. From the evidence of your audit, would you advise...

Stress is applied to a 20-in. steel bar that is clamped in a fixed position at each end. Let Y = the distance from the left end at which the bar snaps. Suppose Y / 20 has a standard beta distribution...

A motor run by a 9.0-V battery has a 20-turn square coil with sides of length 5.0 cm and total resistance 28. When spinning, the magnetic field felt by the wire in the coil is 0.020 T. What is the...

New Built wants to buy back 20,000 shares at $21 per share through a public offering. Shareholders responded by offering 26,500 shares at $21 a share. Suppose you are a shareholder and you offered...

Let {u, v, w, z] be independent. Which of the following are dependent? (a) {u + v, v + w, w + u} (b) {u + v, v + w, w + z, z + u}

how to create KPI for 2 5 agents with name, DNUM number, agent number, performance in excel

Give an example of Thixotropic fluid and mention the value of flow behavior index (n).

Read the following case study and Evaluate a failed organizational change, identify a theory that could have been used to develop the change, and apply that theory to the failed change. An...

Prove that streamline and equipotential lines are perpendicular to each other.

Draw the locations of G, M, and B for a floating body to be in stable equilibrium.

Explain how using base 100, you can develop a test for divisibility by 51, and use it to determine whether 4,012,623,492 is divisible by 51 or not. Show your work.

The triangles in the diagram are congruent. If mF = 40, mA = 80, and mG = 60, what is mB? Two triangles, ABC and EFG, are represented on a grid. Sides AC and GE are marked congruent. Sides AB and EF...

(2) A shaft of diameter D=40mm and 1m long delivers a power of 20kW to a gear system at a speed of 5000rpm. Calculate the shew stress prodered and the angle of twist. The shaft is made of steel irth....

please help 1-6 with work on a separate sheet of paper and explain 1. An 8-g bullet is fired into a 2.5-kg block that is initially at rest at the edge of a frictionless table of height 1 m, as shown...

Pls answer number 1-6 with work and explanation on a seperate paper Pls help! 1. An 8-g bullet is fired into a 2.5-kg block that is initially at rest at the edge of a frictionless table of height 1...

please answer 1-6 on separate sheet of paper with explanation PLS 1. An 8-g bullet is fired into a 2.5-kg block that is initially at rest at the edge of a frictionless table of height 1 m, as shown...

Please answer questions 1-6 on a separate sheet of paper with explanations!!! T 1. An 8-g bullet is fired into a 2.5-kg block that is initially at rest at the edge of a frictionless table of height 1...

please answer questions 1-6 on a seperate sheet of paper with explanations! 1. An 8-g bullet is fired into a 2.5-kg block that is initially at rest at the edge of a frictionless table of height 1 m,...