Question: The diffusion coefficient for some hypothetical small atom in a hypothetical FCC metal is 1 . 3 1 0 - 4 c m 2 s

The diffusion coefficient for some hypothetical small atom in a hypothetical FCC metal is 1.310-4cm2s at 1200C. Assume you know from a previous calculation that the activation energy is 8,633calmol. What is the value of the pre-exponential constant, DO, in cm2s? Express your answer with 4 decimal digits. It will be a small number.
The diffusion coefficient for some hypothetical small atom in a hypothetical

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

Q:

The diffusion coefficient for some hypothetical small atom in a hypothetical FCC metal is 3 . 4 1 0 - 4 c m 2 s at 2 8 0 0 C , and 4 . 6 1 0 - 6 c m 2 s at 9 0 0 C . Determine the activation energy...

Q:

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

Q:

For the following three questions, state if you would solve the problem as being in equilibrium, steady state, or neither. A 20 m thick membrane of Pd is exposed to a hydrogen atmosphere with pH2 =...

Q:

1 According to Fick's first law: A. Diffusion flux is proportional to the concentration gradient B. Diffusion flux is not proportional to the concentration gradient C. The flux is time dependent D....

Q:

WS No 1 : Diffusion The steady - state diffusion flux through a metal plate is 5 . 4 1 0 - 1 0 k g m 2 . s at a temperature of 7 2 7 C and when the concentration gradient is - 3 5 0 k g m 4 ....

Q:

1. The diagram above shows three energy levels of a hypothetical atom. The lowest available energy level is E1 = -5.0 eV. E, = -5.0CV a) Draw arrows on the above diagram showing all possible photon...

Q:

Surface treatments are essential to achieve required material properties in many applications. Nitriding and carburizing are two of the most common methods for surface hardening iron - based alloys....

Q:

Total = 1 0 0 Points Time: 1 1 : 0 0 AM - 1 2 : 1 5 PM 1 . 2 . Calculate the diffusion coefficient of aluminum in gold at 8 2 7 C , whereas the diffusion cocfficient aluminum in gold at 6 2 7 C is 2...

Q:

15. Assuming that a powder has a surface energy of 1.2J/m2, estimate the maximum amount of energy that is available for densification for spherical particles with diameter of 0.5m compacted to a...

Q:

a) A steel sheet 1.8 mm thick has nitrogen atmospheres on both sides at 1200. A steady-state condition is achieved. The diffusion coefficient (D) for nitrogen in steel at this temperature is 6 x...

Q:

Happiness ratings were from 1 (least happy) to 100 (most happy). Data are at the texts website. Use age as the independent variable. a. Make a graph and report whether the trend is linear. If the...

Q:

How many W resistors, each of the same resistance, must be used to produce and equivalent 2.2-k, 3.5-W resistor? What is the resistance of each, and how must they be connected? Do not exceed P = W...

Q:

13 The diagram shows two statues. Each statue is made from three parts. The height of each part, in metres, is shown. a Which statue is taller? Show your working. b What is the difference in height...

Q:

Part Vi: Finite State Machines (15 Use the following simple FSM to answer all questions points) 3 (a) is the string bbabbaaaba valid? Explain why or why not. (b) Is the string baaabab valid? Explain...