Question: The procedures to initializes TM 4 C Port B , so pins 1 , 2 , 3 , 4 as input and the rest are

The procedures to initializes TM4C Port B, so pins 1,2,3,4 as input and the rest are output is?
LDR R0, GPIO_PORTB_DIR_R
MOVB R1,#%11110000
STR R1,[R0]
LDR RO, PORTB
MOVB R1,#%11110000
STR R1,[R0]
LDR RO, GPIO_PORTB_DIR_R *
MOVB R1,#%11100001
STR R1,[R0]
LDR RO, GPIO_PORTB_DIR_R
MOVB R1,#%10101010
STR R1,[R0]
The procedures to initializes TM4C Port B, so pins 1,2,3,4 as

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

#include //include HITECH C Compiler header file /*CONFIGURATION*/ __CONFIG(FOSC_INTOSCIO & WDTE_OFF & PWRTE_ON & BOREN_OFF & LVP_OFF & CP_OFF & CPD_OFF); #define _XTAL_FREQ 4000000L //INTERNAL 4MHz...

Q:

-Use CCS -MSP432 microcontroller Write an assembly program to control the Red, Green, Blue LEDs on the evaluation board according to the statuses of the two switches S1 and S2. Press only S1: RED...

Q:

the code below is what needs to be adjusted for the program to function and it's the only thing I need thank you! ; GPIO.s ; Runs on LM4F120 and TM4C123 ; Implements a NOT gate described in class ;...

Q:

The procedures to initializes TM 4 C Port B , so pins 1 , 2 , 3 , 4 as input and the rest are output is ? LDR R 0 , GPIO _ PORTB _ DIR _ R MOVB R 1 , # % 1 0 1 0 1 0 1 0 STR R 1 , [ R 0 ] LDR R 0 ,...

Q:

Question 1 3 5 points The procedures to initializes TM 4 C Port B , so pins 1 , 2 , 3 , 4 as input and the rest are output is ? LDR RO , GPIO _ PORTB _ DIR _ R MOVB R 1 , # % 1 0 1 0 1 0 1 0 STR R 1...

Q:

Homework 2 1. Enter the code in C that enables GPIO port A, B, and E and clocks in the AHB2 bus. 2. Enter the C code that sets the GPIO port A, pin 0 to input mode. 3. Enter the C code that sets the...

Q:

1. For the following data allocation, show how the variables will be mapped in the memory Assume that the starting address of DATA area is 0x2000000C. All the values should be presented in...

Q:

You wanted to implement a code that adds two words like below. But, you found that the code has compilation errors. Show how the code should be fixed 2. AREA myCode ALIGN main LDR rl, inputl LDRH rl,...

Q:

Lab 1 - Pre-Lab PURPOSE: To become familiar with binary numbers, simulation tools, basic test procedures, and the DE-2 board. PRE-LAB READINGS AND EXERCISES: Prior to the lab period, perform the...

Q:

Question 1: [12 points] Consider the following program and answer the questions given below: CB: DDRB, 2 LDI 816, 0xEF OUT DORD, R16 AGAIN:SBIS PINB, 2 RJMP OVER LDI R16 'Y OUT PORTD, R16 RJMP AGAIN...

Q:

Assume that EBV invested in Newco at the terms in Exercise 10.2, and it is now one year later. Talltree is considering a $10M Series B investment in Newco. Talltree proposes to structure the...

Q:

Four wooden members are joined with metal plate connectors and are in equilibrium under the action of the four forces shown. Knowing that 2.3 FA = kN and FB = 2.1 kN, determine the magnitudes of the...

Q:

6. Modify the AddVariables program so it uses 64-bit variables. Describe the syntax errors generated by the assembler and what steps you took to resolve the errors.

Q:

The first scenario will be a Verbal Judo scenario in which your scenario follows the standard Verbal Judo interaction: You need to ask somebody to modify their behavior either to do something or to...

Q:

5. Understand how cultural values influence conflict behavior.

Q:

8. Explain the relationship between communication and context.

Q:

1. What methods were used in this case to identify the causes of high turnover and low productivity? What other methods could have been used to obtain better data?