Question: The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a _ _ a point load

The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a__
apoint load at the free end
point load at the middle of its length
buniformly distributed load
cover the whole length
dnone of the above

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

The Maestranza Hotel in downtown Mlaga has 94 rooms for which it charges $143 per night. An occupied room costs the hotel $28 in operating costs. There is a 4.5 percent chance that a guest with a...

Q:

The shear force and bending moment are zero at the free end of a cantilever beam, if it carries a _ _ a point load at the free end point load at the middle of its length b uniformly distributed load...

Q:

Shear Force and Bending Moment Diagrams The simply supported beam in Figure 2 . 1 is subjected to a distributed load, a couple moment and a point load. i . Draw the shear and moment diagrams for the...

Q:

A light beam is 7 m long with supports 1 m in each end. The reactions of the supports are 4 1 . 5 N at the left support and 6 3 . 5 N at the right - side support. The beam carries a point load of 3 0...

Q:

EXPERIMENT # 2 : Analyze and draw the Shear force and Bending Moment Diagram for cantilever beam using SAP 2 0 0 0 . Objectives To determine manually the reactions and draw shear force and bending...

Q:

Question 1 [ 1 2 marks ] Simply supported beam with point load at any point: A 1 2 - meter long simply supported beam carries a point load of 1 5 k N located 4 meters from the left support. Calculate...

Q:

Question 3 A simply supported A36 steel universal beam is subjected to a 30 kN point load as shown in Figure 3. You are required to: a) Calculate all the internal forces acting at the cross-section...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

On Form_Load make the form invisible. [hint: use the Hide property]

Q:

Thirty GPAs from a randomly selected sample of statistics students at Oxnard College are available at this text's website. Assume that the population distribution is approximately Normal. The...

Q:

What is the future value of $ 1 , 0 0 0 annunity payments over 8 years, if the interest rate are 1 0 percent

Q:

Please clear answers Which command is equivalent to the init command and is used to change run levels? a. telinit b inittab c. sysinit d. initd All of the files in the run level subdirectories...