Question: The tensile load P on a butt weld fluctuates continuously between 20 and 100 KN. Plates are 20 mm thick. Determine the required length

The tensile load P on a butt weld fluctuates continuously between 20

The tensile load P on a butt weld fluctuates continuously between 20 and 100 KN. Plates are 20 mm thick. Determine the required length L of the weld, applying the Goodman criterion. Cr-0,657 C1 Cs 0,7 Cr-1 K=1,2 Su-427 MPa n=2,5 P h o=P/hL Reinforcement P

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

pow { 0 , { x } , { y } , { x , y } } * pow { 0 , { x } , { y } , { x , y } }

A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm (see figure). When the tensile load P reaches a value of 20 kN, the distance between the gage marks has...

Let A, B be sets. Define: (a) the Cartesian product (A B) (b) the set of relations R between A and B (c) the identity relation A on the set A [3 marks] Suppose S, T are relations between A and B, and...

Isaac Corporation liquidates, with Courtney its sole shareholder receiving the remaining cash of $50,000 plus assets with FMV of $50,000. Courtney's basis in her stock is $22,000. Courtney also...

Q . 2 ( a ) What do you mean by factor of safety? ( b ) Write short note on maximum shear stress theory and maximum distortion energy theory, Q . 3 Define equivalent twisting moment and equivalent...

A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds at the ends. If the plates are subjected to a load of 70 kN, find the size of weld for static as...

WX sxsl from support a .. X Figure (a) shows the cross-section of a built-up simply supported T-beam A-B shown in Figure (b). The distribution of the bending moment due to an applied loading is given...

The experimental result differs from the assumption. The result shows that the ring oscillator frequencies can be grouped into two groups, where the first group is the high frequency group for the...

( a ) For the bolted - connection hanger, How many bolts ( 1 / 2 - in Dia. ) are needed to encounter the LRFD tensile load P = 2 8 0 k , Use A 3 2 5 bolts ( Nominal tensile strength = 9 0 ksi ,...

PROBLEM 2 (50 points) Clapper Electronics produces two models of telephone answering devices, model 102 and model H23. Production process consists of two stages, manufacturing and inspection....

Should ICANNs actions be judged under the rule of reason or be deemed a per se violation of Section 1 of the Sherman Act? The Internet Corporation for Assigned Names and Numbers (ICANN) is a...

Use the first order 2D Taylor series of the function below about the given point to estimate f(-2.9, 0.9). 1 x y Give your answer exactly, or round your answer to 4 decimal places. f(-2.9,0.9) f(x,...

Multiple Choice 1 point Consider the Horizontal and Vertical Analysis for Moorhouse Inc. Net Sales increased substantially in 2 0 2 3 compared to 2 0 2 2 . However, the Analysis declined in 2 0 2 3...

Solution to the initial value problem Sy" + 2y +y = 8(t 2) y(0) = , y(0) = 1 %3D 3 function y(t) is differentiable at time moment t = 2. (T/F) 2. Problem 2. (1 point) Solution to the initial value...

2.The time to failure (in hours) of an electronic components subjected to an accelerated life test is of interest to a senior Engineer. To accelerate the failure test, the units were tested at an...

Journalize the following transactions for the seller, Rodriguez Company, using the gross method to account for sales discounts. Assume a perpetual inventory system. Make sure to enter the day for...

A motor delivers 275 hp at 1000 rpm to the end of a shaft (see figure). The gears at B and C take out 125 and 150 hp, respectively. Determine the required diameter d of the shaft if the allowable...

Solve the preceding problem for a W 250 ( 89 shape with length L = 7.5 m and L = 200 GPa.

Solve the preceding problem if the shaft has outer diameter d2 = 150 mm and inner diameter d1 = 100 mm. Also, the steel has shear modulus of elasticity G = 75 GPa and the applied torque is 16 kN ( m.

_______ theories of personality focus on describing characteristic behavior patterns, such as agreeableness or extraversion.

Which of the following is NOT part of the contemporary view of the unconscious? Repressed memories of anxiety-provoking events Stereotypes that influence our perceptions and interpretations Parallel...

The total acceptance Rogers advocated as part of a growth-promoting environment is called _______ _______ _______.